00197902-03_UM_X-Serie-S_EN.pdf - 第239页

User manual SIPLACE X-Series 4 Setting up and commissioning From software version 710.0 Edition 12/2016 4.3 Setting up the machine 239 4 Fig. 4.3 - 10 Adjusting the machine in the X and Y directions  Use the fork wrench…

4 Setting up and commissioning User manual SIPLACE X-Series

4.3 Setting up the machine From software version 710.0 Edition 12/2016

238

4.3.8 Integrating the machine into the line

 Observe the general warnings in section 4.3.1, page 223.

 Observe the warnings for transportation of the machine in section 4.3.2, page 224.

 For details of tools and equipment, refer to section 4.3.5, page 227.

4.3.8.1 Aligning and adjusting the machines in the line

 With the fork-lift, raise the machine until the weight is taken off the machine feet.

 Determine the PCB conveyor height for the machine in the line and use the hexagon socket

head screw to adjust the height approximately.

 You may need to fit the machine feet to the relevant PCB conveyor height (see 4.3.6 on page

228).

 Position the machine on the free location on the line using the fork-lift.

 Pay attention to the alignment of the PCB conveyors and check the distance to the previous

machine.

 Align the machine in the X and Y direction with the help of the machine spirit level.

 Place the machine spirit level in the X and then the Y direction on the sides of the conveyor

in placement area 1 (see fig. 4.3 - 10

). The board conveyor width has been preset:

Single conveyor 210 mm

Dual conveyor, lane 1 100 mm

Dual conveyor, lane 2 210 mm 4

 Measure the distance between the upper edge of the PCB conveyor belt and the underside.

This distance should be 900 mm, 930 mm or 950 mm.

WARNING

Risk of damage!

If the machine feet on one side hit the ground hard, the fixings may be damaged.

 Lower the machine slowly.

 A second person should look underneath to ensure that all the machine foot touch

the floor at the same time.

PLEASE NOTE

 When using a dual conveyor, always place the spirit level on the outer sides of the

machine for measuring the X direction.

User manual SIPLACE X-Series 4 Setting up and commissioning

From software version 710.0 Edition 12/2016 4.3 Setting up the machine

239

Fig. 4.3 - 10 Adjusting the machine in the X and Y directions

 Use the fork wrench to adjust the setting screw M24x2x120 (item 1 in fig. 4.3 - 11, page 240),

so that the fluid in the machine spirit level does not deviate from its zero point at the required

conveyor height.

4 Setting up and commissioning User manual SIPLACE X-Series

4.3 Setting up the machine From software version 710.0 Edition 12/2016

240

Fig. 4.3 - 11 Presetting the height of the outer machine feet

(1) Setting screw M24x120 for height adjustment (M24x100 at 900 mm machine height)

(2) Outer machine foot

(3) Clamping piece

(4) Hexagon socket-head screw M24x90

 Check the required board conveyor height.

 Once the machine has been aligned, use the torque wrench to tighten the hexagon socket-

head screws M24x90 (item 4) to clamp the clamping pieces at all outer machine feet (item 3).

 Use the hook wrench to unscrew the middle machine feet roughly 135 - 145, until these are

positioned firmly on the ground.

 Make sure that the middle machine feet are not screwed out too far, unbalancing the machine.

PLEASE NOTE

Vibration at low tightening torques!

The tightening torque is 130 Nm. A lower torque could cause the machine to vibrate.

 Use a sufficiently high tightening torque.

(4)

(2)

(1)

(3)