00197902-03_UM_X-Serie-S_EN.pdf - 第376页
6 Station extensions User manual SIPLACE X-Series 6.8 Docking station for the component trolley of the SIPLACE X-Series From software version 710.0 Edition 12/2016 376 6.8.5.1 T ools Y o u will need the following tools t…
User manual SIPLACE X-Series 6 Station extensions
From software version 710.0 Edition 12/2016 6.8 Docking station for the component trolley of the SIPLACE X-Series
375
6.8.5 Adjusting the docking station to the PCB conveyor height
The COT insert of the docking station can be easily converted to PCB conveyor heights of 900,
930 and 950 mm.
6
Fig. 6.8 - 5 Adjusting the COT insert to the PCB conveyor heights
(1) Holes for the PCB conveyor height
(2) Hexagonal nut M8 and washer, 2x each
(3) Hexagonal nut M8 and washer, 2x each
(4) Hexagonal nut M8 and washer, 2x each
(5) Slot for height adjustment
(6) Hexagon socket-head screw M8x40, 6x
(7) Hexagon socket-head screw M5x12, 4x
(8) Guidance
(9) Hexagon socket-head screw M8x18, 2x
(10) Side panel, COT insert
(11) Cover on docking station
(12) Feeder module control unit (FCU)
6 Station extensions User manual SIPLACE X-Series
6.8 Docking station for the component trolley of the SIPLACE X-Series From software version 710.0 Edition 12/2016
376
6.8.5.1 Tools
You will need the following tools to adjust the height of the COT insert:
– Allen wrench, set
– Fork wrench, SW 13
6.8.5.2 Converting the COT insert to other heights
6
6.8.5.3 Converting the COT insert to heights of 900, 930 or 950 mm
6
Fig. 6.8 - 6 Order of conversion steps
Loosen the two hexagon socket-head screws M8x18 (item 9 in fig. 6.8 - 5, page 375) and re-
move the left and right guidance (item 8 in fig. 6.8 - 5
, page 375).
WARNING
Disconnect the docking station from the power supply.
Disconnect the docking station from the compressed air supply.
The weight of the COT insert is approx. 40 kg.
If required, enlist the help of a second person to help you with the conversion.
Follow the steps in the order described.
User manual SIPLACE X-Series 6 Station extensions
From software version 710.0 Edition 12/2016 6.8 Docking station for the component trolley of the SIPLACE X-Series
377
6
Unscrew the two screwed connections (item 3 in fig. 6.8 - 5, page 375).
Loosen the two other screwed connections (item 2 in fig. 6.8 - 5, page 375).
Remove the two M8 hexagonal nuts and washers (item 4 in fig. 6.8 - 5, page 375).
Hold the COT insert by its side (item 10 in fig. 6.8 - 5, page 375) and remove the two hexagon
socket-head screws M8x40 here.
Swivel the COT insert to the next highest position.
Fasten the side panel at this point. Tighten the nuts loosely to do this.
Hold the COT insert by the FCU (item 12 in fig. 6.8 - 5, page 375) and remove the screwed
connections at item 2 in fig. 6.8 - 5
, page 375.
Swivel the COT insert to the next highest position.
Fasten the side panel at this point.
Check that all screwed connections at items 2, 3 and 4 are tightened firmly.
Fasten the right and left guidances (item 8 in fig. 6.8 - 5, page 375) with the hexagon socket-
head screw M8x18 (item 9 in fig. 6.8 - 5
, page 375).
6
CAUTION
Risk of damage!
When raising and lowering the COT insert, cables can be damaged.
When raising and lowering the COT insert, make sure that no cables are damaged.
PLEASE NOTE
If you want to lower the COT insert to a different height, follow the above instructions
in reverse order.