80S-15贴片机.pdf - 第479页

11 Control Unit SIPLACE 80 S/F/G Service M anual Edition 04/97 11 - 10 11.4 Wrap Co nnecti ons of Machine Contro ller MC1 ( left - hand side) 11.4.1 KSP-M18-A16 C8451-A45-A52-X Machine Controller The foll owing jum pers …

100%1 / 484
SIPLACE 80 S/F/G Service Manual 11 Control Unit
Edition 04/97
11 - 9
11.3 Wrap Connections of the Station Computer
11.3.1 KSP-M34-A162 Station Computer
The following jumpers must be present:
11.3.2 IEC-Bus Module
The following jumpers must be present:
Connection Significance
WL2/1
→
WL2/2
Primary adapter, color
WM1/1
→
WM1/2 AMS-INIT connected to assembly
WJ1/1
→
WJ1/2 BCLK on AMS-Bus
WL1/10
→
WL1/11 CCLK on AMS-Bus
WM2/1
→
WM2/2 32 KHz cycle connected to RTC
WL1/3
→
WL1/4 XACK on AMS bus
WM1/7
→
WM2/10 AMS-INT4 on IREQ12
WM1/8
→
WM2/11 AMS-INT5 on IREQ15
WJ1/8
→
WM1/10 SW-INT0 on AMS-INT7
WJ1/9
→
WM1/9 SW-INT1 on AMS-INT6
Tab. 11.3 - 1 Wrap connections of station computer KSP-M34-A162
Connection Significance
WJ1/2
→
WJ2/2 TI9914A switched on
WJ1/4
→
WJ2/4 I/O basic address 2B8H
WJ1/6
→
WJ2/6
WM1/3
→
WM2/3 DACK1
WM1/6
→
WM2/6 DRQ1
WM1/10
→
WM2/10 IRQ1
Tab. 11.3 - 2 Wrap connections of the IEC-bus module
11 Control Unit SIPLACE 80 S/F/G Service Manual
Edition 04/97
11 - 10
11.4 Wrap Connections of Machine Controller MC1 (left-
hand side)
11.4.1 KSP-M18-A16 C8451-A45-A52-X Machine Controller
The following jumpers must be present:
NOTE:
Wrap connections which differ from the standard configuration are marked by an asterisk (*).
Connection Significance
WM1/11
→
WM1/12 Operation without 80C187 co-processor
WM2/11
→
WM2/12 AMS-INIT connected to assembly
WJ2/1
→
WJ2/2 SRAM and DPRAM connected to Vcc
WC2/1
→
WC2/2 SMP HOLD sets M18 to HOLD
WM4/2
→
WM1/2 Interrupt MOD1 on IR2 Master
WM4/3
→
WM2/5 Interrupt SCC on IR3 Master
WM4/4
→
WM1/1 Interrupt MOD0 on IR4 Master
WM4/6
→
WM2/2 Interrupt WAKEUP on IR6 Master
WM4/7 *
→
WK2/8 Interrupt AMS-INT7 on IR7 Master
WM2/6 *
→
WK2/6 SOFTINT on AMS-INT5
WC1/1
→
WM1/6 SCC-Clock, 4.91 MHz
WJ3/1 *
→
WJ3/2 WAKEUP on IO address 1100H
WJ3/1
→
WJ3/6 WAKEUP on IO address 1100H
WF2/2
→
WF2/4 32K DPRAM in upper half of segment
WN2/1
→
WN2/2 DPRAM address on AMS bus 50000H
WN2/2
→
WN2/4 DPRAM address on AMS bus 50000H
WJ1/1
→
WJ2/5 0 waitstates command delay
WJ1/4
→
WJ2/6
4 waitstates command delay for SMP bus
access
WJ1/4
→
WJ2/7
WJ1/4
→
WJ2/8
WF1/2
→
WF1/3 V24 D2 on SCC
WM3/9
→
WM4/10 64 Kilobyte EPROMs
WM3/10
→
WM4/11 64 Kilobyte EPROMs
WM3/11
→
WM4/12 64 Kilobyte EPROMs
Tab. 11.4 - 1 Wrap connections of the KSP-M18-A16 C8451-A45-A52-X machine controller
SIPLACE 80 S/F/G Service Manual 11 Control Unit
Edition 04/97
11 - 11
11.5 Wrap Connections of Machine Controller MC2
(right-hand side, applies to 80S only)
11.5.1 KSP-M18-A16 C8451-A45-A51-X Machine Controller
The following jumpers must be present:
NOTE:
Wrap connections which differ from the standard configuration are marked by an asterisk (*).
Connection Significance
WM1/11
→
WM1/12 Operation without 80C187 co-processor
WM2/11
→
WM2/12 AMS-INIT connected to assembly
WJ2/1
→
WJ2/2 SRAM and DPRAM connected to Vcc
WC2/1
→
WC2/2 SMP HOLD sets M18 to HOLD
WM4/2
→
WM1/2 Interrupt MOD1 on IR2 Master
WM4/3
→
WM2/5 Interrupt SCC on IR3 Master
WM4/4
→
WM1/1 Interrupt MOD0 on IR4 Master
WM4/6
→
WM2/2 Interrupt WAKEUP on IR6 Master
WM4/7 *
→
WK2/7 Interrupt AMS-INT6 on IR7 Master
WM2/6 *
→
WK2/5 SOFTINT on AMS-INT4
WC1/1
→
WM1/6 SCC-Clock, 4.91 MHz
WJ3/1
→
WJ3/6 WAKEUP on IO address 1000H
WF2/2
→
WF2/4 32K DPRAM in upper half of segment
WN2/1
→
WN2/2 DPRAM address on AMS bus 50000H
WN2/2
→
WN2/4 DPRAM address on AMS bus 50000H
WJ1/1
→
WJ2/5 0 waitstates command delay
WJ1/4
→
WJ2/6
4 waitstates command delay for SMP bus
access
WJ1/4
→
WJ2/7
WJ1/4
→
WJ2/8
WF1/2
→
WF1/3 V24 D2 on SCC
WM3/9
→
WM4/10 64 Kilobyte EPROMs
WM3/10
→
WM4/11 64 Kilobyte EPROMs
WM3/11
→
WM4/12 64 Kilobyte EPROMs
Tab. 11.5 - 1 Wrap connections of the KSP-M18-A16 C8451-A45-A51-X machine controller