SIPLACE X-Series (SIPLACE X-Series S, from SC 708.1) Edition 05/2015 EN User manual.pdf - 第212页
3 Technical data and assemblies User manual SIPLACE X-Series 3.10 Component trolley From software version 708.1 Version 05/2015 212 3 Fig. 3.10 - 7 SIPLACE X-Series changeover table, front view (1) Locking latc hes (2) C…
User manual SIPLACE X-Series 3 Technical data and assemblies
From software version 708.1 Version 05/2015 3.10 Component trolley
211
3.10.6 SIPLACE X-Series changeover table
The front slider guides of the feeder modules are placed on the insertion aid (item 1 in fig.
3.10 - 6
). When pushed in, the slider guides of the
feeder module (item 12 and 13 in fig. 3.9 - 2
, page 177) slide on the guide profile (item 2 in fig.
3.10 - 6
) up to the stop rail (item 4 in fig. 3.10 - 6). A centering hole (item 5 in fig. 3.10 - 6) on the
stop rail accommodates the X feeder module centering pin "front" (item 4 in fig. 3.9 - 1
, page 176).
At the same time, the changeover table locking latch (item 1 in fig. 3.10 - 7
, page 212) engages
onto the locking roller (item 1 in fig. 3.9 - 1
, page 176) of the feeder module. The centering pin
"rear" (item 12 in fig. 3.9 - 1
, page 176) on the upper side of the feeder module is accommodated
by the recess in the centering bar (item 3 in fig. 3.10 - 6
).
3
Fig. 3.10 - 6 Changeover table, SIPLACE X-Series, rear view
(1) Insertion aid
(2) Guide profile (Ω profile)
(3) Centering bar for holding the "back" centering pin for X feeder modules
(4) Stop bar
(5) Centering holes
(6) Contact for switching the safety switch of the EMERGENCY STOP circuit
(7) Hand guard
3 Technical data and assemblies User manual SIPLACE X-Series
3.10 Component trolley From software version 708.1 Version 05/2015
212
3
Fig. 3.10 - 7 SIPLACE X-Series changeover table, front view
(1) Locking latches
(2) Centering pin on the changeover table
(3) Compressed air coupling
(4) Earthing (ground) pin
(5) Centering hole on the changeover table
User manual SIPLACE X-Series 3 Technical data and assemblies
From software version 708.1 Version 05/2015 3.10 Component trolley
213
3.10.7 Mount of additional tape reel
3
Fig. 3.10 - 8 Mount for additional tape reel (X-Series)
(1) Mount of additional tape reel, item no. 00141217-xx
(2) Mounting device for the support
X-Series feeder modules can process component tapes without problems if the lateral offset be-
tween the feeder module and the tape reel does not exceed 60 mm. If a predefined setup means
that the maximum permitted offset cannot be maintained, we recommend that you use the mount
for an additional tape reel (item 1). Simply insert the mount into the holder (item 2) and push it until
the offset is less than the maximum permitted value of 60 mm. The component trolley has 5 hold-
ers in total. Each tape reel mount can hold 2 tape reels, which means that up to ten 15" (381 mm)
reels can be positioned above the tape container.
Max. 60 mm