SIPLACE X-Series (SIPLACE X-Series S, from SC 708.1) Edition 05/2015 EN User manual.pdf - 第296页

5 Working with the machine User manual SIPLACE X-Series 5.9 Carrying out a sight check From software version 708.1 Version 05/2015 296 5.9.3 Checking the PCB support s  Check the position of the magnetic PCB supports on…

100%1 / 430
User manual SIPLACE X-Series 5 Working with the machine
From software version 708.1 Version 05/2015 5.9 Carrying out a sight check
295
5
Check the multicolor status display (item 3 in fig. 5.9 - 1, page 294).
– If it lights up green, the feeder module is on standby.
– If it lights up orange, it is signaling a warning. The text of the warning
appears on the LCD display (item 4 in fig. 5.9 - 1
, page 294). The LEDs shine accordingly
for Smart Feeders.
– If the status display lights up red, a malfunction has occurred. The error message
appears on the LCD display (item 3 in fig. 5.9 - 1
, page 294). The LEDs shine accordingly
for Smart Feeders.
A list of the LCD and status displays on the operator panel is given in section 5.11
, page
310
. 5
A list of the LED and status displays on the Smart Feeder operator panel is given in sec-
tion 5.11.2
, page 311. 5
If the status display is off, the cause may be as follows: 5
– The feeder module is not in the current setup.
– The feeder module is defective.
– The feeder module has been disabled (due to a drop in pressure, for example)
5.9.2 Splicing the tapes in good time
5
CAUTION
Problems with cover foil withdrawal!
If the cover foil tears, this could lead to problems with the cover foil withdrawal.
There is an integral blade (item 2) for easily cutting the on the 8 and 12 mm X tape feeder
modules.
PLEASE NOTE
Late splicing of tapes
Late splicing of tapes can lead to prolonged down times.
Splice the tapes early enough so that the feeder modules do not run out of compo-
nents.
PLEASE NOTE
Early splicing of tapes
Early splicing of tapes can have the following consequence: when the old tape is rolled
up onto the new reel, the new reel could become too full and the tape will slide off it and
get caught up. This will again result in pick-up errors and prolonged down times.
Splice the tapes at the right time so that the old and new tapes do not get caught.
5 Working with the machine User manual SIPLACE X-Series
5.9 Carrying out a sight check From software version 708.1 Version 05/2015
296
5.9.3 Checking the PCB supports
Check the position of the magnetic PCB supports on the lifting table:
– Make sure that the PCB supports do not collide with components on the underside of the
PCBs.
– In addition, make sure that the PCB supports do not collide with the PCB conveyor pan-
els.
– Only use PCB supports as described in section 6.14
, page 399.
5.9.4 Mount of additional tape reel
5
Fig. 5.9 - 2 Mount of additional tape reel
(1) Mount of additional tape reel, item no. 00141217-xx
(2) Mounting device for the support
5
Max. 60 mm
User manual SIPLACE X-Series 5 Working with the machine
From software version 708.1 Version 05/2015 5.9 Carrying out a sight check
297
X-Series feeder modules can process component tapes without problems if the lateral offset be-
tween the feeder module and the tape reel does not exceed 60 mm.
If a predefined setup means that the maximum permitted offset cannot be maintained, we recom-
mend that you use the mount for an additional tape reel (item 1). Simply insert the mount into the
holder (item 2) and push it until the offset is less than the maximum permitted value of 60 mm. The
component trolley has 5 holders in total. Each tape reel mount can hold 2 tape reels, which means
that up to ten 15" (381 mm) reels can be positioned above the tape container.
5.9.5 Inserting separating plates into the tape container
The separating plate has different edges and can be inserted into the tape container in two
ways. If spindles are used, the recesses for the spindles in the separating plate point upwards
(see item 4 in fig. 5.9 - 3
). If you do not use spindles, the rounded edge of the separating
plate points up (see item 5 in fig. 5.9 - 3
).
Insert the separating plates as shown in fig. 5.9 - 3 and remember that the smallest division
of the tape container is a 2x division. This will help avoid placement errors.
Check that the separating plates engage in the same positions on the three guide rails. Oth-
erwise the separating plate will be offset or bent.