SIPLACE X-Series (SIPLACE X-Series S, from SC 708.1) Edition 05/2015 EN User manual.pdf - 第46页
2 Operational safety User manual SIPLACE X-Series 2.1 Safety instructions From software version 708.1 Version 05/2015 46 2.1.2 Qualified personnel Qualified or adequat ely trained personnel means that these people are fa…
User manual SIPLACE X-Series 2 Operational safety
From software version 708.1 Version 05/2015 2.1 Safety instructions
45
2 Operational safety
2.1 Safety instructions
2.1.1 Conventions for the use of hazard symbols
This user manual contains notes that must be observed to guarantee your personal safety and to
avoid damage to equipment. These notes are highlighted by warning triangles and are indicated
as follows according to the level of risk:
2
2
2
2
2
DANGER
Definition
Danger, as used in this user manual, means that death, severe injury or considerable
damage to equipment will occur if the danger instructions are not followed.
WARNING
Definition
Warning, as used in this user manual, means that death, severe injury or considerable
damage to equipment may occur if the warning instructions are not followed.
CAUTION
Definition
Caution, as used in this user manual, means that slight injury or damage to equipment
may occur if the caution instructions are not followed.
PLEASE NOTE
Definition
A note, as used in this user manual, provides information on the product or indicates a
part of the user manual that requires particular attention.
2 Operational safety User manual SIPLACE X-Series
2.1 Safety instructions From software version 708.1 Version 05/2015
46
2.1.2 Qualified personnel
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and preventive maintenance of placement machines and add-on devices and are suit-
ably qualified, e.g.
– have been trained, instructed or authorized to switch on and off, isolate, earth and identify
electrical circuits and system components in accordance with normal safety standards.
– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-
cordance with normal safety standards.
– Have received first aid training.
2.1.3 Important notes on operational safety
The following points MUST be observed in order to maintain operational safety:
2.1.3.1 General
The operational safety of SMD placement machines can be guaranteed only if the system is
used as prescribed and in accordance with the instructions in the user/preventive mainte-
nance manuals.
Always follow any safety regulations specific to your country.
Make sure that the warning labels are always clearly identifiable and always easily readable.
Replace any damaged warning or notice labels. Replace any labels that are missing.
The machine key for releasing the covers on the machine must be kept in a safe place where
it is only accessible to qualified personnel.
2
If it is necessary to work on the machine and you do not have adequately trained personnel
within your operation, always call in a ASM Assembly Systems GmbH&Co.KG service engi-
neer! ASM Assembly Systems GmbH&Co.KG will not accept liability for any damage or con-
sequential damage that is the result of unauthorized/incorrect work.
If particularly hazardous situations are identified while the machine is in use, the machine
owner must immediately notify the manufacturer in writing so that appropriate action can be
taken to reduce the potential danger.
PLEASE NOTE
Owner's responsibility
The machine owner, and only the machine owner, is responsible for the safekeeping of
the machine key and for ensuring that it is handed over to authorized persons.
User manual SIPLACE X-Series 2 Operational safety
From software version 708.1 Version 05/2015 2.1 Safety instructions
47
2
2.1.3.2 Safety of operators and other persons
Machine operators must only carry out work for which they have been adequately trained and
with which they are totally familiar.
NEVER open one of the protective covers if you are not totally familiar with the use and func-
tioning of the machine! Do not open the protective covers during operation unless you are told
to do so in this manual or in the station software dialog.
The placement machine may only be operated if there is a component trolley present and
docked at each location.
NEVER place your head or arms in the gantry and lifting table traveling range while the station
is switched on!
For your own safety, wear work clothes that conform to the guidelines of the professional as-
sociation or to the regulations of your country, i.e. safety shoes, hair net or no wide sleeves
etc.
Reduce the risks by not wearing scarves, chains or ties at your work post.
People with long hair must wear a protective head covering.
2
WARNING
Severe injuries and damage to equipment in the case of incorrect usage!
In the event of the machine being incorrectly used, movement of the gantries or lifting
tables, for example, can lead to severe injuries and considerable damage to equipment.
Safe operation of the machine requires correct usage by qualified staff with observance
of all warnings.
Some work on the machine (e.g. setting up) requires training that goes beyond the scope
of this manual.
WARNING
Dangerous voltage levels!
The system is electrically driven. Certain parts are still live when the main power switch
is off and the mains plug has been disconnected. Switch off the main switch, disconnect
the mains plug and wait for 5 minutes.
There is a risk of death, severe injury and/or considerable damage to equipment if these
instructions are not followed.
Switch off at the main switch and disconnect the placement machine from the power
supply before carrying out any work on live components.
Lock the machine as described in section 2.9, page 99.