M3plus_OperationManual_e.pdf - 第11页
iv 1. Safety 1.3 Warning labels The following warning labels are affixed to the machines. Check the information on the label and always follow its instructions. This section explains warning labels affixed to surface mou…
iii
■ Cautions during operation
c
CAUTION
Always stop the machine before installing the parts feeder into the machine. Hands or other
parts of your body might otherwise be caught in the moving parts.
c
CAUTION
Do not press the emergency stop button during operation, except in case of emergency.
c
CAUTION
Always turn off the power by using the correct procedure. Using hasty or incorrect procedures
to turn off power might damage the disk in the machine.
c
CAUTION
When installing push-up pins on the push-up plate, set them in positions where they will not
interfere with the conveyor rails or other parts when the push-up plate is raised.
c
CAUTION
When you are using a machine not equipped with a nozzle station, you must change the nozzle
by hand if it is not a specified nozzle. In this case, always first press the emergency stop button.
c
CAUTION
If an abnormality occurs during warm-up, immediately stop the machine, find the cause of the
problem and eliminate it.
■ Other warnings during operation, maintenance and adjustment
w
WARNING
ALWAYS SHUT OFF THE POWER AND AIR SUPPLY BEFORE REPLACING PARTS OR PER-
FORMING REPAIRS.
w
WARNING
DURING TEACHING OR MAKING MACHINE ADJUSTMENTS, ALWAYS KEEP ALERT SO THAT
YOU CAN STOP THE MACHINE WHENEVER NEEDED.
w
WARNING
SAFETY DEVICES (SAFETY INTERLOCKS) THAT STOP MACHINE OPERATION SHOULD
ALWAYS BE IN CORRECT OPERATING CONDITION.
w
WARNING
THE MACHINE SHOULD NEVER BE USED IN LOCATIONS WITH FLAMMABLE GAS OR IN
EXTREMELY DIRTY OR POLLUTED ENVIRONMENTS.
1. Safety
iv
1. Safety
1.3 Warning labels
The following warning labels are affixed to the machines. Check the information on the
label and always follow its instructions. This section explains warning labels affixed to
surface mounters and all other related machines including dispensers, solder paste print-
ers and peripheral equipment.
w
WARNING
WARNING
CLOSE COVER WHILE OPERATING
Possible injury
Safety cover
23001-5E-2A
w
WARNING
KEEP THE SAFETY COVER CLOSED DURING MACHINE OPERATION. INJURIES MIGHT OCCUR
FROM TOUCHING MOVING PARTS DURING OPERATION WHILE THE SAFETY COVER IS STILL
OPEN.
WARNING
DO NOT TOUCH THIS SWITCH
MOVING MACHINE MAY CAUSE INJURY
Possible injury
Safety cover switch
23001-5E-2B
w
WARNING
DO NOT TOUCH THE SAFETY COVER SWITCH DURING MACHINE OPERATION. INJURIES
MIGHT OCCUR FROM TOUCHING MOVING PARTS DURING OPERATION WITH THE SAFETY
COVER SWITCH DEACTIVATED.
WARNING
Do not put In
hand through
openIng.
MovIng parts can
pInch hand.
Possible injuries from getting caught between moving parts
23001-5E-2J
w
WARNING
NEVER PLACE HANDS IN THE MACHINE DURING OPERATION. HAND OR FINGERS MIGHT BE
CAUGHT BETWEEN MOVING PARTS AND COVERS, CAUSING SERIOUS INJURIES.
v
1. Safety
Possible injuries from touching internal parts
WARNING
Gears and cutters can
cause severe personal injury.
Tu r n p ower off before
servicing or cleaning.
23001-5E-2M
w
WARNING
DO NOT PUT YOUR HANDS INTO THE MACHINE WHILE THE POWER IS TURNED ON. HAND OR
FINGERS MIGHT BE CAUGHT IN GEARS OR CUT BY CUTTER BLADES, CAUSING INJURIES.
c
CAUTION
HIGH VOLTAGE!
Electrical shock hazard
23001-5E-2C
c
CAUTION
Use caution since electrical shocks might occur from touching or coming in contact with the
power supply section inside the panel.
HOT!
Possible burns if touched
23001-5E-2D
c
CAUTION
The motor becomes extremely hot during and shortly after operation, so do not touch it!