00196497-07_SM_SXDX12_en.pdf - 第185页
Service Work Conveyor 3.7.1 Replacing the Fixed/Guide Castors Component Trolley SX Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 185 3.7 3 . 7 C o m p o n e n t T r o lle y S X Component Trolley SX 3.7.1 3 . 7 . 1 R e p la…
Service Work Conveyor
Conveyor 3.6.9 Changing Fixed Side Left/Right (EC Only)
184 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
Converting the adjustment units:
► Loosen the screws (10) (2x two) fastening the two ad-
justment units (9).
► Move the adjustment units to the opposite side by
pulling on the width adjustment belt.
► Fit the adjustment units on the opposite side in the re-
verse order. Also observe the following instructions:
NOTICE!
Installation instructions
Make sure that the screws which were previously sealed
with locking varnish are once again sealed with locking
varnish.
Converting the sensor rail (FS01 only):
NOTICE!
This work only needs to be performed on the conveyor
with FS01. It is not needed and no replacement tasks are
needed for conveyors with FS02.
► Push the sensor rail off the guidance pins (2).
► Dismantle the three sonar sensors (4) and fit these
again on the opposite side of the sensor rail (1). (fixed
side right to left side and fixed side left to right side)
► Dismantle the three plastic guidances (3) and fit
these again on the opposite side of the sensor rail.
► Run the sonar sensor cables accordingly on the op-
posite side. Make sure that these cables do not rub
against any parts and are not pinched.
► Fit the sensor rail onto the guidance pins.
► Check the setting of the sonar sensors and reteach
them, if required. (see "4.6.2 Teaching the Sonar
Sensor" [ ➙ 278]).
Service Work Conveyor
3.7.1 Replacing the Fixed/Guide Castors Component Trolley SX
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 185
3.7
3.7 Component Trolley SX
Component Trolley SX
3.7.1
3.7.1 Replacing the Fixed/Guide Castors
Replacing the Fixed/Guide Castors
Parts, Equipment and Tools
Removal
► Move the changeover table out of the machine.
► Place the changeover table down on its side, on a suitable surface.
► Undo the screws fastening the fixed or guide castor to to replaced and then remove the castor.
Installation
► Follow the removal instructions in reverse order for installation.
NOTICE
SX and DX table
Unless specified otherwise, all specifications apply to both the SX and DX tables.
1. Fixed castor [03058705-xx]
2. Guide castor [03059198-xx]
CAUTION
Heavy machine part!
The changeover table must be placed on one side in order to remove the fixed/guide castors.
The changeover table is extremely heavy! You will need 2 people to perform this task
Service Work Conveyor
Component Trolley SX 3.7.2 Replacing the Insert Feeder [03002898-xx]
186 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
3.7.2
3.7.2 Replacing the Insert Feeder [03002898-xx]
Replacing the Insert Feeder [03002898-xx]
Parts, equipment and tools
Select the right insert feeder:
Removal
► Move the component trolley out of the machine.
► Loosen the screw fastening the guide profile and remove the guide profile.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
Insert feeder [03002898-xx]
Suitable for:
▪ X-Series component trolley
▪ Component trolley SX1/SX2 (30 or 60 tracks)
▪ Manual table X-Series S
Insert feeder [03085635-xx]
Suitable for:
▪ Manual table DX series
CAUTION
Installation instructions
► Make sure that the insert is aligned properly with the guidance behind it. You must be able
to push feeder modules into the feeder location without edge interference.