00196497-07_SM_SXDX12_en.pdf - 第291页
Settings 4.7.1 Times for Setting the Throttle on the Cutter (From SW707. 1) Settings on the Cutter Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 291 4.7 4 . 7 S e t t in g s o n t h e C u t t e r Settings on the Cutter 4.7…
Settings
Conveyor Settings 4.6.8 Lifting Table
290 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
4.6.8
4.6.8 Lifting Table
Lifting Table
4.6.8.1
4.6.8.1 Setting the Parallelism and Height of the Lifting Table Plate
Setting the Parallelism and Height of the Lifting Table Plate
Overview
Setting
► Use the software to move the conveyor sides to maximum width. (See "3.6.1 Loosening the Convey-
or Side Clamps" [ ➙ 143])
► Loosen the screws fastening the lifting table plate but do not remove the lifting table plate.
► Use the software to clamp the lifting table (without board).
► Underneath the fastening screws, there are setting screws (socket-head 5). Use these setting
screws to set the lifting table plate so that it has no play between it and the clamping edge.
► Check all four corners of the lifting table for any play.
► Check the setting by clamping a board into place. Check all corners to see whether there is any play.
► Calibrate the zero position of the lifting table motor.
See also
4.6.5 Calibrating the Motors in the Conveyor [ ➙ 287]
1.2 Preparatory Work... [ ➙ 13]
DANGER
Press the EMERGENCY STOP!
Before performing adjustment work you must ensure that the lifting table has been secured
against movement!
Lifting table plate (example of SX1/SX2 V2 shown)
1. Lifting table plate
2. Fastening screws for lifting table plate
NOTICE
Single, dual conveyor
The setting is shown in the diagram using the example of a lifting table unit for the dual conveyor
(DC). Setting the single conveyor (SC) follows the same procedure.
Settings
4.7.1 Times for Setting the Throttle on the Cutter (From SW707.1) Settings on the Cutter
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 291
4.7
4.7 Settings on the Cutter
Settings on the Cutter
4.7.1
4.7.1 Times for Setting the Throttle on the Cutter (From SW707.1)
Times for Setting the Throttle on the Cutter (From SW707.1)
NOTICE!
From SW707.1
From software version 707.1, the throttle times on the
cutter are displayed in the station software.
Cutter SX1/SX2, DX1/DX2
[03063781-xx]
X-Series S
[03066690-xx]
Moving the balde out 160 to 220 ms 175 to 200 ms
Moving the blade in 210 to 230 ms 200 to 250 ms
Settings
Settings on the Component Trolley 4.8.1 Setting the Changeover Table Height
292 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
4.8
4.8 Settings on the Component Trolley
Settings on the Component Trolley
4.8.1
4.8.1 Setting the Changeover Table Height
Setting the Changeover Table Height
4.8.1.1
4.8.1.1 Adjusting the Changeover Table to the Board Transport Height
Adjusting the Changeover Table to the Board Transport Height
4.8.1.2
4.8.1.2 Adjusting the Changeover Table Height to the Machine
Adjusting the Changeover Table Height to the Machine
Changeover table with a board transport height of
950 mm
► Loosen the screws (4) for the top and bottom stop-
pers.
► Lift the changeover table plate. You may need to en-
list the help of a second person for this.
► Loosen the pulleys (2) and screw these tight again at
the required height:
⇨ 900 mm ± 15 mm SMEMA height
⇨ 930 mm ± 15 mm SMEMA height
⇨ 950 mm ± 15 mm SMEMA height
These heights correspond with the holes (1) (from top to
bottom).
► Insert the screws (4) for the top and bottom stoppers
in the corresponding holes (3).
1. Height adjustment wheel.
► To adjust the height to the COT insert, push the
changeover table into the machine until the stopper
block of the table is positioned under the bracket of
the table height check.
► Use the adjustment wheel to lift the changeover table
until the surfaces are almost but not quite touching.
The tolerance between the function surfaces is +/
- 2.5 mm.