00196497-07_SM_SXDX12_en.pdf - 第78页

Service Work Conveyor Control 3.3.6 Repla cing the LAN Card [03112190-xx] 78 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 3.3.6 3 . 3 . 6 R e p la c in g t h e L A N C a r d [ 0 3 1 1 2 1 9 0 - x x ] Replacing the LAN Car…

100%1 / 334
Service Work Conveyor
3.3.5 Replacing the Hotlink Interface Card [03052135-xx] Control
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 77
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
► Dismantle and remove the BoxPC from the machine.
(See "3.3.3 Replacing the Control Computer BoxPC" [ ➙ 72])
► Open the covers above the plug-in cards.
► Undo the screw fastening the Hotlink card and remove the Hotlink card.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
CAUTION
Installation instructions
► Make sure that the plug-in card is correctly fitted into its slot.
► Check whether the correct driver is installed and, if it is not, install it.
► Connect the "hotlink interface/power" cable [03042074-xx]. Follow the diagram below for
this.
BoxPC 627B/C
BoxPC ABP402-A iBase
"Hotlink interface/power" cable
► If you are replacing the hotlink interface/power cable
(2), you will need to loosen and open the cover (1) on
the hard drives.
However, if you are continuing to use the old hotlink
interface/power cable, this step is not required.
Service Work Conveyor
Control 3.3.6 Replacing the LAN Card [03112190-xx]
78 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
3.3.6
3.3.6 Replacing the LAN Card [03112190-xx]
Replacing the LAN Card [03112190-xx]
If a 3D Coplan or a barcode scanner is installed, the "LAN card PCI Gigabit SEMPRE NC1000-1"
[03112190-xx] is needed in addition.
This LAN card is used in the "BoxPC ABP402-A CPU1020E 2xPCI SSD-80GB (iBase)" [03120423-xx]
in machines from serial number N001.
Parts, Equipment and Tools
▪ LAN Card PCI Gigabit SEMPRE NC1000-1 [03112190-xx]
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
► Dismantle and remove the BoxPC from the machine.
(See "3.3.3 Replacing the Control Computer BoxPC" [ ➙ 72])
► Open the covers above the plug-in cards.
► Undo the screw fastening the LAN card and remove the LAN card.
BoxPC ABP402-A iBase
1. Free slot for the LAN card
2. Hotlink card
Service Work Conveyor
3.3.6 Replacing the LAN Card [03112190-xx] Control
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 79
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
Overview of IP Ad dresses
Overview of IP Addresses
For further information on making the IP settings, refer to the installation manual
Installation Manual Windows Embedded Standard 7 [00197737-xx]
CAUTION
Installation instructions
► Make sure that the plug-in card is correctly fitted into its slot.
► Make the IP settings for the LAN card (see below).
IP address Subnet mask Comment
SIPLACE LAN 172.22.xxx.xxx 255.255.0.0 LAN connection on the
computer
CIN box 192168255239 255255255224 LAN connection on the
computer
Station computer 192168255249 255255255224 Additional LAN card for
the coplan computer
Coplan computer 192168255253 255255255224