BM料架治具使用手册.pdf - 第47页
Feeder Inspection Unit 4.1 Adjusting Wheel Position 4.1−4 DX1OEC−31−240−B0 Supplying Air 1. Open the air valve. 2. Check the air pressure. Use the regulator to adjust the pressure if necessary. (0.4 MPa (4.1 kgf/cm 2 )) …
Stopper
Air conductor
4.1 Adjusting Wheel Position
Feeder Inspection Unit
4.1−3
DX1OEC−31−240−B0
4.1.3 Preparations for Inspection
Attaching the Gauge Jig
1. Attach the gauge jig along the guides of the clamp stand.
=HINT=
When attaching/detaching the gauge jig and feeder, pushing the clamp reset lever enables the
clamp to be released.
This allows the gauge jig and feeder to be attached/detached easily.
Stopper
Gauge jig
Clamp reset lever
Push
Guide
Air conductor
Clamp stand
2. Ensure that the stopper of the gauge jig and air
conductor of the clamp stand have been fitted
properly without any gap.
=REMARKS=
• To ensure c lamping, av oid pus hing the
clamp reset lever when fitting the stopper
to the air conductor.
• Check if the fitting is proper for accurate
inspection. If there is a gap, the gauge jig
can be displaced.
Turning Power ON
1. Turn ON the breaker switch.
2. Turn ON the main switch.
Breaker switch
ON
ONOFF
Main switch
Feeder Inspection Unit
4.1 Adjusting Wheel Position
4.1−4
DX1OEC−31−240−B0
Supplying Air
1. Open the air valve.
2. Check the air pressure.
Use the regulator to adjust the pressure if necessary. (0.4 MPa (4.1 kgf/cm
2
))
=REMARKS=
Depending on models, the supplied pressure may differ. The tape feeders, however, can be
operated as usual.
(1) (3)
(2)
Regulator
Pressure
gauge
Knob
(1) Pull down the knob to
unlock the regulator.
(2) Turn the knob to
adjust the pressure.
(3) Push up the knob
to lock the regulator
in place.
Valve
4.1 Adjusting Wheel Position
Feeder Inspection Unit
4.1−5
DX1OEC−31−240−B0
Checking the Wheel Position Hole (or Vacuum Position Hole)
1. Set the camera view select lever to the R side.
2. Adjust the focus displayed on the monitor using the adjust knob (Z).
3. Using the knobs (X, Y and Z), adjust the camera position so that the wheel position hole or vacuum
position hole may be aligned with the center of the cross hairs, while observing the X/Y graduation
plates and the monitor.
4. Then, tighten the lock knobs (X, Y and Z) to secure the camera.
=HINT=
To ensure measurement accuracy, tighten the lock knobs to secure the camera in position.
8
V
Lock knob (Y)
Lock knob (X)
Graduation
plate (X)
Graduation
plate (Y)
Adjust knob (X)
X slider
Lock
knob (Z)
Adjust
knob (Z)
Z slider
Y slider
Adjust
knob (Y)
Align the edge of the X slider with
the predetermined graduation.
Align the edge of
the Y slider with
the predetermined
graduation.
V
8
12
16
24
32
44
56
72
MOTOR
V
0603W
AIR
W
=HINT=
How to utilize the graduation plate
• The marks on the graduation plate is used for rough positioning with respect to the wheel position
hole of the gauge jig.
• Align the edge of the X/Y sliders and graduation plate according to the feeder type and width. This
enables you to find the target wheel holes easily.
Then, make fine−adjustment of the camera position for the wheel position hole of the gauge jig.
• The tables below show how the positions on the X/Y graduations plates correspond to the feeder
type.
Pickup position
X slider position Y slider position
Motorized feeder
Pickup position
Wheel positions for 8 − 72 mm
Pneumatic double feeder
(For 0603)
Pneumatic feeder
Pneumatic double feeder
(Other than 0603)