AL1_SiplaceX-en.pdf - 第215页
1 - 53 S tudent Guide SIPLACE X Edition 02/2005 5 Collect&Place-Head 20 53 5.5.3 Assembly with adju sting tool of nozzle ch anger 20 segment C&P- head So that the safe distance get s large sufficiently between he…
1 - 52
Student Guide SIPLACE X
5 Collect&Place-Head 20 Edition 02/2005
52
5.5.2 Detail view of nozzle changer 20 segment C&P- head
Fig. 5.5 - 2 Detail view of nozzle changer 20 segment C&P head
Legend left picture in Fig.8.5-2
(1) X/Y position of calibration fiducial (2) Locking plate
(3) Nozzle garage (4) The parallel pins to the centering maga-
zine
(5) Microswitch for magazine recognition (6) Tipping over lever to remove the magazine
(7) Locking Pin of magazine (8) 4 push button to the mount on the nozzle
changer carrier
(9) green LED check for a right mount of all
magazines on the nozzle changer carrier
(10) X/Y position of calibration fiducial of
nozzle reject box
conveyor direction
1
2
3
4
5
6
way of counting of the
magazines
nozzle reject box
component reject box
1
2 3
4 5 6 7
8 9 10 11 12
4
8
5 4
6
7
6
2
3
1
9
10
1 - 53
Student Guide SIPLACE X
Edition 02/2005 5 Collect&Place-Head 20
53
5.5.3 Assembly with adjusting tool of nozzle changer 20 segment C&P- head
So that the safe distance gets large sufficiently between head and nozzle changer and this one
strained himself isn't exhausted by the machine tolerances, the edition of the nozzle changer, the
so-called docking unit is adjusted to 20 mm +/-0,2mm by means of a teaching to the head. The
adjustment tool will be placed at the position of the pressure control valve. The pressure control
valve has to be unscrewed (not removed). Now it is possible to put on the adjusting tool without
any problems. The support of the nozzle changer carrier has to be adjusted with washers in its
height until the the nominal distance is acchieved and then it has to be fixed.
Fig. 5.5 - 3 Assembly with adjusting tool of nozzle changer at C&P20- head (part no. 03035130-0x)
Please Note for assembling the nozzle changer :
During assembling the nozzle changer keep attention that the component reject box can be easily
removed. Don´t use to long screws, otherwise the component reject box will be fixed.
Please Note for assembling the adjusting tool:
During assembling the adjustment tool keep attention that this will be done between transport and
component table. Otherwise it is not possible to put the head beyond the transport .
20mm +/- 0,2mm
1 - 54
Student Guide SIPLACE X
5 Collect&Place-Head 20 Edition 02/2005
54
5.5.4 Control unit for nozzle changer of the C&P heads
The nozzle changer are controlled depend on the configuration of the location at the machine via
CAN Bus (SLIO Main- und Sub-Distributor). In future with the SW 505 the nozzle changer are con-
trolled via the "One Wire Bus". Soleniods control the pneumatic rotary drives and open or close
the nozzle changer..
Legende
5.5.5 Pneumatic plan for nozzle changer
Fig. 5.5 - 4 Pressure air supply for the nozzle changer
The air pressure supply of the nozzle changer will be assembled by the T-piece as shown in the
picture below. A additional Y- piece is necessary for the optional 2
nd
Nozzle changer carrier.
(1) SUB-D connector machine CAN Bus (2) SUB-D connector Option ( reject boxes / 24 V)
(3) ribbon cable nozzle changer 1 (4) ribbon cable nozzle changer 2
3
area-
coding
LED check
noz.ch. 2
12
34
LED check DLM
noz.ch. 1
3
4
2
1
Gantry 1 - 4
4
3
2
1
Bulkcase
Feeder
COT 1-4
2,5 bar
adjustable
Nozzle
changer
1 2
34
Nozzle changer
Gantry 1 - 4
2,5 bar
adjustable
Docking unit
1 - 4
5 bar
adjustable
Conveyor
5 bar
adjustable
5 bar
adjustable
1 2 3 4
Compressed air distributor block
Tape cutter
1 - 4
4 3
21
+
nozzle changer
C&P20
(4,5bar)