EUKYX-199-4110_G5S2_Instruction_Vol4_E.pdf - 第111页
EUKYX 1-62 199-4100 5. Cleaning of vacuum nozzles • V acuum N ozzle Cle aning T ool L ist Noz z le Ty p e Section Dirtiness T ype Masking tape Pin gauge + Insert ion Jig Drill Ai r Blow Jig + Water Washing Hydraulic Clea…
EUKYX
1-61199-4100
5. Cleaning of vacuum nozzles
5. Cleaning of vacuum nozzles
Periodically clean the vacuum nozzles to maintain reliable and stable component picks and
placement.
• It is advisable that the nozzles be cleaned at least once a week.
The nozzle for 0402 recommends the cleaning every 3 or 4 days.
• Change cleaning frequency according to various frequency of use and accumulation of debris
along with certain environmental conditions.
• When the vacuum suction force weakens or a nozzle constantly fails to pick or place
components, it is required to check the nozzle for debris and cleanliness.
Do not grasp this part strongly during the
nozzle cleaning.
Otherwise, the nozzle may be damaged.
When it is necessary to hold the nozzle firmly,
try to grasp the collar portion.
When a recognition error occurs frequently,
rub the back of the collar approximately
20 times with a toothbrush.
Taper part
F4A46
Note
EUKYX
1-62199-4100
5. Cleaning of vacuum nozzles
• Vacuum Nozzle Cleaning Tool List
Nozzle
Type
Section Dirtiness Type
Masking
tape
Pin
gauge
+
Insertion
Jig Drill
Air Blow
Jig +
Water
Washing
Hydraulic
Cleaning
Machine
Wiping
using a
Cloth,
etc.
Cleaning
Frequency
Spring
Nozzle
for 0201
to 0402
Nozzle Tip Attached Solder
Paste
Required Required
Appropriately
Nozzle Tip
Hole
Flux, Clogged
with Foreign
Object
Required Required Required
Nozzle
Inside Hole
Flux
Required
Once a week
Spring
Sliding
Section
Air
Contamination
Paper Fiber
Required Required
Nozzle
Outside
Required
Filter
Change
Spring
Nozzle
for 0603
to 1608
Nozzle Tip Attached Solder
Paste
Required Required
Appropriately
Nozzle Tip
Hole
Flux, Clogged
with Foreign
Object
Required Required Required
Nozzle
Inside Hole
Flux
Required
Once a week
Spring
Sliding
Section
Air
Contamination
Paper Fiber
Required Required
Nozzle
Outside
Required
Filter
Change
Rigid
Nozzle
Nozzle Tip Attached Solder
Paste
Required Required
Once a week
Nozzle Tip
Hole
Flux, Clogged
with Foreign
Object
Required Required Required
Nozzle
Inside Hole
Flux
Required
Nozzle
Outside
Required
Filter
Change
EUKYX
1-63199-4100
5.1 Vacuum Nozzle Cleaning procedure
5.1 Vacuum Nozzle Cleaning procedure
Remove Nozzle Filter
Refer to "5.3 Nozzle Filter Removal Procedure"
in this chapter for details.
Blow air to Vacuum Nozzle
Confirm that there is no clog in pick-up hole
Refer to "5.4 Method of Blow air" in this chapter
for details.
Confirm the clog in the top of pick-up hole by
the magnifying glass.
Refer to "5.5 Cleaning of high-speed nozzle
hole part with pin gauge" in this chapter for details.
Remove Vacuum Nozzle
Refer to "5.2 Method of detaching vacuum
nozzle" in this chapter for details.
Insert the nozzle filter
Refer to "5.7 Nozzle Filter Insertion Procedure"
in this chapter for details.
Reference
Reference
Reference
Reference
Reference
F4A47
NOTICE
In the case that the ultra-sonic cleaning and solvent
are used for the nozzle cleaning, the adhesive
applied onto the nozzle joint section would be
degraded, which could cause adhesive ablation and
damage to the nozzle unit.