EUKYX-199-4110_G5S2_Instruction_Vol4_E.pdf - 第274页
EUKYX 3-109 199-4100 3.10 Others Error ID Error Name, Description, Cause, and Remedy 4b20 0a P .C .B Height Measurement Erro r of the re sult m easu red by a ma ster j ig (he ight ) Che ck if t he mas ter jig ( heig ht) …
EUKYX
3-108199-4100
3.10 Others
Error ID Error Name, Description, Cause, and Remedy
4b0c02 Nozzle Confirmation Error before pick up comp
The remains component was found on a nozzle during production.
Please confirm whether there is an error in the P.C.B.
4b0c03 Nozzle Confirmation Error before pick up comp (Detect After Discard)
Because a component was found on a nozzle, it stopped after disposal.
Please confirm and clean up the nozzle if this error continues. And please check the status
of a PCB.
4b0e01 Splicing tape set error
The joint part of splicing tape is not correctly set. Please extract a feeder and check
whether the tape has separated from the guide.
-----
4b1201 Press in error / Insertion error
There is an error with the component pressed in or Insertion
Open safety cover and confirm the component on P.C.B. Please remove it or revise it
4b19ff Zeroing of single axis error
Timeout in zeroing of single axis.
-----
4b2001 P.C.B Height Measurement
Abnormal measured value was detected.
Check the measurement position.
4b2002 P.C.B Height Measurement
Abnormality occurred for communication with a sensor
-----
4b2003 P.C.B Height Measurement
The abnormality number of times of measured value was beyond a set point. Running is
stopped.
-----
4b2004 P.C.B Height Measurement
The abnormality number of times of measured value was beyond a set point.
-----
4b2005 P.C.B Height Measurement
A measurement result is abnormal(measure in arbitrary position)
Check the measurement position.
4b2006 P.C.B Height Measurement
Surpass a measurement range. (+ direction)
-----
4b2007 P.C.B Height Measurement
Surpass a measurement range. (- direction)
-----
4b2008 P.C.B Height Measurement
Detected a curve more than permission values. (+ direction)
-----
4b2009 P.C.B Height Measurement
Detected a curve more than permission values. (- direction)
-----
EUKYX
3-109199-4100
3.10 Others
Error ID Error Name, Description, Cause, and Remedy
4b200a P.C.B Height Measurement
Error of the result measured by a master jig (height)
Check if the master jig (height) has some dirt and foreign particles.
4b200b P.C.B Height Measurement
Failed in wearing height revision.
-----
4b200c P.C.B Height Measurement
An abnormal measurement was detected by the multipoint measurement.
Check the measurement position.
4b200d P.C.B Height Measurement
Recovery by the multipoint measurement failed because the measurement result was
insufficient.
Check the measurement position.
4b 2011 P.C.B Height Measurement
Measurement time-out
-----
4b2081 P.C.B Height Measurement
Abnormality occurred for communication with a sensor
-----
4b2082 P.C.B Height Measurement
Failed in wearing height revision.
-----
4b2083 P.C.B Height Measurement
Measurement time-out
-----
4b2084 P.C.B Height Measurement
The coordinate where the height measurement was impossible was appointed.
Please appoint a coordinate in a measurable range.
4b2101 SSC network abnormal
There is abnormal in SSC network.
Please confirm the cable of SSC network.
4b2102 SSC network abnormal
There is a problem in connection to Servo Amplifier(XY).
(1) Shut down the machine and check the connection between the position board and
amplifier.
(2) Check whether or not the servo amplifiers are damaged.
4b2103 SSC network abnormal
There is a problem in connection to Servo Amplifier(Head).
(1) Shut down the machine and check the connection between the position board and
amplifier.
(2) Check whether or not the servo amplifiers are damaged.
4b2301 Feeder (Servo Error)
Alarm Code:A0 - Internal Parameter Error (Breakdown of Control P.C.B.)
Please replace the feeder. (Do not disconnect the feeder in powering on, otherwise it may
cause the inside data broken.)
EUKYX
3-110199-4100
3.10 Others
Error ID Error Name, Description, Cause, and Remedy
4b2302 Feeder (Servo Error)
Alarm Code:A1 - Over Current Error (Foreign substances in the tape feeding drive section)
Confirm whether or not the tape is being jammed on the path./ Confirm the reel to operate
smoothly./ Confirm whether or not some components and dust are being caught in the
sprocket./ Confirm whether or not some components and dust are being caught in the tape
feeding gear.
4b2303 Feeder (Servo Error)
Alarm Code:A2 - Others
-----
4b2304 Feeder (Servo Error)
Alarm Code:A3 - Others
-----
4b2305 Feeder (Servo Error)
Alarm Code:A4 - Main Circuit Power Supply Error (Please check the power supply voltage.)
(G04)
Please check the power supply voltage.
4b2306 Feeder (Servo Error)
Alarm Code:A5 - Fault Speed Error (Tape catching)
Confirm whether or not the tape is being jammed on the path.
Confirm the reel to operate smoothly.
Confirm whether or not some components and dust are being caught in the sprocket.
Confirm whether or not some components and dust are being caught in the tape feeding
gear.
4b2307 Feeder (Servo Error)
Alarm Code:A6 - Others
-----
4b2308 Feeder (Servo Error)
Alarm Code:A7 - Fault Load Error (Tape twisting, Catching foreign substances)
Confirm whether or not the tape is being jammed on the path.
Confirm the reel to operate smoothly.
Confirm whether or not some components and dust are being caught in the sprocket.
Confirm whether or not some components and dust are being caught in the tape feeding
gear.
4b2309 Feeder (Servo Error)
Alarm Code:A8 - Encoder Error (Breaking wire, Breakdown of control P.C.B. and Defective
servo motor)
Please replace the feeder.
4b230a Feeder (Servo Error)
Alarm Code:Ab - System Error
Please replace the feeder. (It may be caused by trouble of the control P.C.B..)
4b230b Feeder (Servo Error)
Alarm Code:Ac - Reckless Run Detection Error
Please replace the feeder. (It may be caused by trouble of the control P.C.B..)
4b230c Feeder (Servo Error)
Alarm Code:Ad - Excessive deviation in position
If the error occurs frequently, replace the feeder. (It may be caused by trouble of the control
P.C . B . .)