EUKYX-199-4110_G5S2_Instruction_Vol4_E.pdf - 第174页
EUKYX 3-10 199-4100 3.1 Safety Device Error ID Error Name, Description, Cause, and Remedy 400896 Ser vo A larm Zero s et mis s ala rm ----- 40089F Ser vo A lar m Batter y warning ----- 40 0 8E0 Se r vo Alar m Over -Regen…
EUKYX
3-9199-4100
3.1 Safety Device
Error ID Error Name, Description, Cause, and Remedy
400835 Servo Alarm
Command Frequency Error
Exchange Position Board
400836 Servo Alarm
Error received data.
Is there any cable twisted or bent? Check it.
400837 Servo Alarm
Parameter Error
Check Servo parameter. Exchange Servo Amplifier if no problem with Servo parameter.
400842 Servo Alarm
Linear Servo control error detected
Is there any error of setup Linear Encoder or wiring of Power Line? Check it.
400845 Servo Alarm
Main circuit elem overheat
Drive with blocking tact, or take the ambient temperature of the Amplifier down.
400846 Servo Alarm
Servo Motor overheat
Drive with blocking tact, or take the ambient temperature of the Motor down.
400847 Servo Alarm
Cooling Fan Error
Exchange cooling fan of Servo Amplifier
400850 Servo Alarm
Overload1
(1)Please perform Optimize.
(2)Please check whether there is no error in Sliding detect of a driving system or in motor
wiring or not.
400851 Servo Alarm
Overload2
Please check whether there is no error in Sliding detect of a driving system or in motor
wiring or not.
400852 Servo Alarm
Error in excess
Please check whether there is no error in Sliding detect of a driving system or in motor
wiring or not.
40088A Servo Alarm
USB communication time-out
-----
40088B Servo Alarm
USB Communication Error
-----
400891 Servo Alarm
Multi-axes Amplifier Temperature warning
Take the ambient temperature of the multi-axes amplifier down.
400892 Servo Alarm
Battery disconnection warning
-----
EUKYX
3-10199-4100
3.1 Safety Device
Error ID Error Name, Description, Cause, and Remedy
400896 Servo Alarm
Zero set miss alarm
-----
40089F Servo Alarm
Battery warning
-----
4008E0 Servo Alarm
Over-Regenerative alarm
Drive with blocking tact.
4008E1 Servo Alarm
Overload alarm1
Drive with blocking Tact.
4008E3 Servo Alarm
Absolute position counter warning
Perform noise strategies of encoder or exchange servo amplifier.
4008E4 Servo Alarm
Parameter warning
Check out servo parameter.
4008E6 Servo Alarm
Servo forced stop alarm
EM1, emergency stop input of Servo amplifier is off.
4008E7 Servo Alarm
Controller emergency stopping warning
outputted emergency stop from Controller.
4008E8 Servo Alarm
No. of Rot dropping warning of Cooling Fan
Exchange the Cooling fan.
4008E9 Servo Alarm
Main circuit off warning
Main circuit is Off.
4008EB Servo Alarm
another axis warning
Error in another axis in the same P.C.B. Please remove the factor of error.
4008EC Servo Alarm
Overload alarm2
Please perform Optimize.
4008ED Servo Alarm
Output Watt over warning
Driver with blocking Tact.
40 0 911 Servo Alarm
Power drive Error, Over-current
Check out motor wiring or exchange both motor and driver
400921 Servo Alarm
Overload Alarm
Check out motor wiring or exchange both motor and driver. Either, Confirm that the blocking
exists with cutter pieces.
EUKYX
3-11199-4100
3.1 Safety Device
Error ID Error Name, Description, Cause, and Remedy
400931 Servo Alarm
Speed Alarm
Readjust motor gain.
400941 Servo Alarm
multi-cycle Error
Check out the motor wiring or exchange the motor.
400942 Servo Alarm
The value of variation counter is out of the range
Check out the wiring of Origin sensor. Or, Exchange driver.
400951 Servo Alarm
Power Drive detected temperature error
Ambient Temperature is high. Exchange driver.
400961 Servo Alarm
Sensor Error
Check Motor Encoder wires. Or, exchange the motor.
400962 Servo Alarm
Sensor Error
Check Motor Encoder wires. Or, exchange the motor.
400971 Servo Alarm
high drive Voltage
Insufficient power. Exchange driver.
400972 Servo Alarm
Low drive Voltage
Check out the drive power wiring putted in Driver. Or, check out DC48V.
400991 Servo Alarm
Reading Error on permanent memory
Exchange the driver.
400992 Servo Alarm
Writing Error on permanent memory
Exchange the driver.
400998 Servo Alarm
CPU Error
Exchange the driver.
400999 Servo Alarm
Parameter Error
Confirm the changed value of Parameter.
400a08 Head Interlock Error
Releasing the brake is impossible during Servo On.
-----
400b01 Feeder preparation complete
A pick up miss comp or disengaged Latch was detected.
Open the safety cover and confirm that there is no interference with the head, and then,
release the ready feeder.
400c01 Nozzle stocker down time out
Nozzle stock unit lower bound detection 1 was not turned on in prescribed time.
Please confirm the lower bound detection 1 sensor of nozzle stock unit.