PCBRM_User_Manual_R9.pdf - 第21页

PCBRM15 & PCBRM System 5.2 User’s Manual Chapter 2: Requirements/Machine Overview Part No. 4005.00.906 2-7 Y-Axis Board Lock X-Axis Carrier Lock Z-Axis Adjustment Wheel Board Locks Carrier Arms Carrier Arms Arm Lock(…

PCBRM15 & PCBRM System 5.2 User’s Manual Chapter 2: Requirements/Machine Overview

Part No. 4005.00.906 2-6

(L)

(M)

(K)

(C)

(E)

(F)

(G)

(I)

(J)

(B)

(A)

(Q)

(P)

(R)

(O)

(N)- option

(Q)

(H)

(D)

(E) Main Power Switch – ON/OFF provides electrical power to the systems.

(F) Relatch Switch – Resets Main Power after unit is turned off or Emergency stopped.

(G) White Light – Indicates Main Power is on.

(H) Transformer Breakdown Light – Indicates failure of transformer coil isolation.

(I) Green Light – Indicates solder is molten and the machine is ready to cycle.

(J) Cycle Switch – Activates the Cycle Duration with Mode Switch in Automatic Mode.

(K) Temperature Controller – Controls temperature of solder.

(L) Ramp Up Flow Rate - Adjusts motor start speed of the pump, either quickly or slowly. To increase

ramp time, turn knob counter-clockwise. To decrease, turn clockwise.

(M) Ramp Down Flow Rate - Adjusts motor stop speed of the pump, either quickly or slowly. This can

help to produce a better solder joint. To increase ramp time, turn the knob counter-clockwise, to

decrease turn clockwise.

Note:

FLOW RATE INFLUENCES THE TOTAL DURATION/PROCESS CYCLE. RAMP DOWN FLOW RATE

INFLUENCES THE TIME WHEN THE AIR IS ACTIVATED FOR THE AIR CLEANING SYSTEM (APS

OPTION). FOR SOLDERING, SET RAMP DOWN TO "0". FOR DESOLDERING, SET TO "10".

(N) Flow Well Heater Box (option) – When external heaters are required for heating large flow wells.

(O) Heater Control Right (high/low) – Adjusts right flow well heater from low to high temp.

(P) Heater Control Left (high/low) – Adjusts left flow well heater from low to high temp.

(Q) Left & Right Plugs – Plug heater for flow wells here.

(R) ON/OFF Switch

PCBRM15 & PCBRM System 5.2 User’s Manual Chapter 2: Requirements/Machine Overview

Part No. 4005.00.906 2-7

Y-Axis Board Lock

X-Axis

Carrier Lock

Z-Axis

Adjustment Wheel

Board

Locks

Carrier Arms

Carrier

Arms

Arm Lock(s)

X-Axis Rail

2.5 PCBRM15 - Carrier Overview

Carrier Arms: Hold board level to solder wave. Adjust to width of board.

X-Axis Carrier Lock: Locks carrier in place once board is aligned over flow well.

Board Locks: Locks board in carrier arms.

Y-Axis Board Lock: Sets y-axis position of board.

Z-Axis Adjustment: Adjusts height of carrier/board in relationship to the flow well.

X-Axis Lock (preheater): Sets x-axis position of carrier/board to flow well.

Arm Lock(s): Lock carrier arms on x-axis rail to hold PCB.

X-Axis Rail: Moves PCB left to right from loading PCB to flow well.

PCBRM15 & PCBRM System 5.2 User’s Manual Chapter 2: Requirements/Machine Overview

Part No. 4005.00.906 2-8

Cleaning Hood (option)

Flow Well

Heater Control (option)

Compliant Arm Locks

Preheater

X-Rail

Handle

Flow Well

Z-Axis

Positioning

Knob

X-Axis Stop

(preheater)

2.6 PCBRM System 5.2 – System Overview