00195166-0402_SM_D4_EN.pdf - 第246页
Settings Conveyor Setting the fixed con veyor si de (single and dua l conveyor) 246 Serv ice Manual SIPLACE D4 6.5.2.2 Wide ning the Conveyor (Flexible Dual Conveyor for Single Conveyor Mode) X In the SITEST co nveyor me…
Settings
Setting the fixed conveyor side (single and dual conveyor) Conveyor
Service Manual SIPLACE D4
245
6.5.2 Setting the fixed conveyor side (single and dual conveyor)
6.5.2.1 General Notes
6-28: SITEST "Set fixed conveyor side"
The fixed conveyor side can be set in SITEST if required.
If the position taught for the fixed conveyor side is saved, these values will be used for the function
Move all conveyor edges in standard position
.
The default values will be overwritten and will need to be retaught.
If these dimensions are incorrectly set on the single or dual conveyor, the PCB reference corner may
be moved, leading to fiducial errors during placement.
Two requirements for changing the fixed conveyor sides:
Extra wide conveyor – moves the fixed conveyor side 34 mm outwards.
Widened conveyor – moves the sides of the 2nd conveyor to the limit switch.
Single conveyor control mode (D series up to 380 mm/HF, X lines up to 450 mm)
NOTE:
If you want to change the conveyor mode from "widened" to "extra wide" (or vice versa), you
need to first move the conveyor into standard mode.
NOTE:
This menu is protected with the SIPLACE Service password.
NOTE:
In the SR/MC station SW, the fixed conveyor side of all lanes can be adjusted in the conveyor
firmware (flexible). However, this may only be set with the SITEST software.
NOTE:
In the D series machines, you need to remove the clamping rings on the fixed conveyor side in
advance.
Settings
Conveyor Setting the fixed conveyor side (single and dual conveyor)
246 Service Manual SIPLACE D4
6.5.2.2 Widening the Conveyor (Flexible Dual Conveyor for Single Conveyor Mode)
X In the SITEST conveyor menu
Options and Configurations
select the menu
Change Widening of
Conveyor
to widen the conveyor.
X The conveyor sides of the 2nd conveyor lane (right side fixed (lane 1 left side fixed)) are moved to
the limits.
X The SITEST SW will ask you to connect the lifting tables.
Widening the board conveyor (from its standard width) allows you to use boards up to 380 mm wide.
Widening the board conveyor from the mode "Widened" to the mode "excess width" allows you to place
boards up to a width of 430 mm.
6-29: Setting the "fixed conveyor side" in SIPLACE D series
NOTE:
The fixed conveyor side should be adjusted only with the SITEST software and the width
adjustment devices. This ensures that the conveyor runs straight.
Settings
Setting the fixed conveyor side (single and dual conveyor) Conveyor
Service Manual SIPLACE D4
247
6.5.2.3 Connecting the Dual Conveyor Lifting Tables
X Remove the lifting table plate on conveyor lane 2 in PA1 and on lane 1 in PA2.
X Loosen the lockscrew(s) (4) and use a screwdriver to push the hexagonal circlip over the shaft on
lifting table 1.
X Perform lifting table connection for all placement areas (arrangement rotated by 180°.)
X Configure the new conveyor mode in SIPLACE Pro
6.5.2.4 Converting the Single Conveyor Mode Back to Flexible Dual Conveyor Mode
X In the SITEST conveyor menu Options and Configurations, select the menu
Change Widening of
Conveyor
to set the default conveyor mode.
X The moveable conveyor side of conveyor 1 (right side fixed (track 1 left side fix)) is moved to a small
conveyor width (default).
X The SITEST SW will ask you to disconnect the lifting tables. Do so.
X The SITEST SW will now use the conveyor control SW to move the fixed side of conveyor 2 (right
side is fixed (lane 1 left side fixed)) back to its standard position. Check the distances between the
two fixed conveyor lanes. (see section (6.5.2.2 Widening the Conveyor (Flexible Dual Conveyor for
Single Conveyor Mode)
J
246 ) )
X Now adjust the conveyor width of both tracks to the required values.
NOTE:
This option is only a mechanical necessity when you use the dual conveyor as a single
conveyor. The two lifting tables move parallel when they are connected.
6-30: Connecting lifting tables (e.g. PA1 conveyor lane 2)
The drive shaft (1) is connected to the piston
rod of the pneumatic cylinder. This shaft is
connected to the shaft of the lifting table for
conveyor lane 1. The lifting table drive shaft
has an additional rod with a hexagon circlip.
This rod is pushed over the shaft of lifting table
1.
Direction of transport (2).
Direction (3) in which the hollow shaft from
lifting table 2 (1 in PA 2) is to be moved to lifting
table 1 (2 in PA 2).
Lock screws (4).
NOTE:
When converting the dual conveyor to a single conveyor (flexible dual conveyor), connect the
lifting tables when requested to do so by SITEST (we recommend doing this without the
compressed air supply to the lifting table).
This function is supported by SIPLACE Pro .