00195166-0402_SM_D4_EN.pdf - 第247页

Settings Setting the fixed conveyor si de (single and dual co nveyor) Conveyor Service Manual SIPLACE D4 247 6.5.2.3 Connecting the Dual Conveyor Lif ting T ables X Remove the lifting table plat e on conveyor lane 2 in P…

Settings

Conveyor Setting the fixed conveyor side (single and dual conveyor)

246 Service Manual SIPLACE D4

6.5.2.2 Widening the Conveyor (Flexible Dual Conveyor for Single Conveyor Mode)

X In the SITEST conveyor menu

Options and Configurations

select the menu

Change Widening of

Conveyor

to widen the conveyor.

X The conveyor sides of the 2nd conveyor lane (right side fixed (lane 1 left side fixed)) are moved to

the limits.

X The SITEST SW will ask you to connect the lifting tables.

Widening the board conveyor (from its standard width) allows you to use boards up to 380 mm wide.

Widening the board conveyor from the mode "Widened" to the mode "excess width" allows you to place

boards up to a width of 430 mm.

6-29: Setting the "fixed conveyor side" in SIPLACE D series

NOTE:

The fixed conveyor side should be adjusted only with the SITEST software and the width

adjustment devices. This ensures that the conveyor runs straight.

Settings

Setting the fixed conveyor side (single and dual conveyor) Conveyor

Service Manual SIPLACE D4

247

6.5.2.3 Connecting the Dual Conveyor Lifting Tables

X Remove the lifting table plate on conveyor lane 2 in PA1 and on lane 1 in PA2.

X Loosen the lockscrew(s) (4) and use a screwdriver to push the hexagonal circlip over the shaft on

lifting table 1.

X Perform lifting table connection for all placement areas (arrangement rotated by 180°.)

X Configure the new conveyor mode in SIPLACE Pro

6.5.2.4 Converting the Single Conveyor Mode Back to Flexible Dual Conveyor Mode

X In the SITEST conveyor menu Options and Configurations, select the menu

Change Widening of

Conveyor

to set the default conveyor mode.

X The moveable conveyor side of conveyor 1 (right side fixed (track 1 left side fix)) is moved to a small

conveyor width (default).

X The SITEST SW will ask you to disconnect the lifting tables. Do so.

X The SITEST SW will now use the conveyor control SW to move the fixed side of conveyor 2 (right

side is fixed (lane 1 left side fixed)) back to its standard position. Check the distances between the

two fixed conveyor lanes. (see section (6.5.2.2 Widening the Conveyor (Flexible Dual Conveyor for

Single Conveyor Mode)

J

246 ) )

X Now adjust the conveyor width of both tracks to the required values.

NOTE:

This option is only a mechanical necessity when you use the dual conveyor as a single

conveyor. The two lifting tables move parallel when they are connected.

6-30: Connecting lifting tables (e.g. PA1 conveyor lane 2)

 The drive shaft (1) is connected to the piston

rod of the pneumatic cylinder. This shaft is

connected to the shaft of the lifting table for

conveyor lane 1. The lifting table drive shaft

has an additional rod with a hexagon circlip.

This rod is pushed over the shaft of lifting table

 Direction of transport (2).

 Direction (3) in which the hollow shaft from

lifting table 2 (1 in PA 2) is to be moved to lifting

table 1 (2 in PA 2).

 Lock screws (4).

NOTE:

When converting the dual conveyor to a single conveyor (flexible dual conveyor), connect the

lifting tables when requested to do so by SITEST (we recommend doing this without the

compressed air supply to the lifting table).

This function is supported by SIPLACE Pro .

Settings

Conveyor Moving the Fixed Conveyor Edge for ’Extra Wide Conveyor’

248 Service Manual SIPLACE D4

6.5.3 Moving the Fixed Conveyor Edge for ’Extra Wide Conveyor’

The standard positions of the fixed conveyor sides are preset.

X In the SITEST conveyor menu

Options and Configurations

and select the menu

Conveyor

Excess Width,

to set the conveyor mode "Extra wide".

X The fixed conveyor side of conveyor 2 (right side fixed (track 1 left side fix)) remains in its position.

X The ’fixed conveyor of track 1(right side fixed (track 2 left side fix)) is moved 34mm to the outside.

This allows you to use wider boards. The flexible conveyor side on lane 2 (lane 1 left fixed) can now

be set to accommodate boards which are wider than 216 mm (242 mm).

NOTE:

This operating mode is possible for D machines with single or dual conveyors.

ATTENTION:

After the conversion process, you need to measure/calibrate the board reference corner and the

conveyor sides and then save this information in the machine data.