80S-2080F480F5.pdf - 第541页
SIPLACE 80S-20/F4/F5 User M anual 9 Maintenance 05/99 Issue from Software Version SR.405.xx 9.6 IC Head (SIPLACE 80F4/F5) 9 - 75 - Sequence of work in Fig. 9.6.9 A Clean al l the supp orting s urfaces wi th a dry brush. …
9 Maintenance SIPLACE 80S-20/F4/F5 User Manual
9.6 IC Head (SIPLACE 80F4/F5) 05/99 Issue from Software Version SR.405.xx
9 - 74
Fig. 9.6.9 Maintaining the nozzles
- Key to Fig. 9.6.9
(The item numbers of the nozzles and diaphragms will be found in section 17.2.2.)
1 Maintenance of the nozzles with diaphragm 2 Nozzle, type 418
3 Diaphragm 4 Sleeve
5 Nozzle, type 419 6 Maintenance of the nozzles without diaphragm
7 Nozzle, type 416 8 Nozzle, type 417
SIPLACE 80S-20/F4/F5 User Manual 9 Maintenance
05/99 Issue from Software Version SR.405.xx 9.6 IC Head (SIPLACE 80F4/F5)
9 - 75
- Sequence of work in Fig. 9.6.9
A Clean all the supporting surfaces with a dry brush.
B Dry clean the annular surface of the sleeve.
C Rub a little talcum powder into the supporting surface of the diaphragm.
D Clean the suction hole.
E Check the suction surface.
9.6.6.3 Replacing the Diaphragm of the Nozzles
Replace the diaphragm if damaged. All relevant details are shown in the following diagram.
Fig. 9.6.10 Replacing the diaphragm of the nozzles
- Key to Fig. 9.6.10
(The item numbers of the nozzles and diaphragms will be found in section 17.2.2.)
1 Nozzle, type 418 2 Diaphragm for 418 nozzle type
3 Sleeve for 418 nozzle type 4 Supporting surface
5 Nozzle, type 419 6 Diaphragm for 419 nozzle type
7 Sleeve for 419 nozzle type 8 Supporting surface
9 Maintenance SIPLACE 80S-20/F4/F5 User Manual
9.6 IC Head (SIPLACE 80F4/F5) 05/99 Issue from Software Version SR.405.xx
9 - 76
- Sequence of work in Fig. 9.6.10
A Pull off the sleeve.
B Remove the diaphragm.
C Clean the sleeve with alcohol and dry it before refitting.
D Rub a little talcum powder into the supporting surface of the new diaphragm and keep it absolutely
grease-free.
When you replace the sleeve, push it in as far as it will go.
9.6.6.4 Inserting Nozzles into the Nozzle Changer
After maintenance insert the nozzles by hand into their correct assigned places (by referring to the notes
you took when you removed them ) in the nozzle changer.
Insert the nozzle removal tool into each nozzle in turn and turn the nozzle anticlockwise until it locks in the
nozzle changer. Lift the tool vertically upwards and out.
Close the safety hoods and swivel doors and switch the machine on.
Have the allocations of nozzles to garage numbers displayed by making the following selection :
Gantry 1 functions
→
Nozzle configuration IC head
NOTE
You can only use this function when you have returned the current nozzle not by hand but, as described,
by using the
Return nozzle
function.
A table will be shown on the screen with the garage numbers (pick-up location numbers) and the actual
and programmed occupancies. Insert the nozzles into the nozzle changer in accordance with the ACTUAL
assignments.
Check to make sure the nozzles are properly latched.
NOTE
If the nozzles are not properly latched this will lead to errors in picking up the nozzle, while incorrectly
assigned nozzles will result in component pick-up errors.
At the start of placement the current nozzle as specified in the placement program will be picked up.