Forte Max Manual.pdf - 第31页

ForteMAXDispensingSystemAddendum Recipe Creation

4.4 Dual Simultaneous Dispensing

The following steps are required to create a dual simultaneous dispensing recipe:

• Create the recipe

• Create a pattern

• Add dispensing instructions

• Create a Container

• Place the Container

4.4.1 Creating a Recipe for a Multi-up Panel

This section outlines the steps required to create the recipe for the multi-up board, layout option 2

(Figure 3-4). The following recipe will dispense a line around all the cells (red squares) shown in

Figure 4-2. For detailed programming information, refer to the Canvas Dispensing Software User Guide.

1 2 3 4 5 6 7 8 9 10 11 12

4

3

2

1

6130139 REV 1

STRAIGHT

B,1

B,2

2,1 2,2 2,3 2,4 2,5 2,6

1,1 1,2 1,3 1,4 1,5 1,6

4,1 4,2 4,3 4,4 4,5 4,6

A2

A1

3,1 3,2 3,3 3,4 3,5 3,6

A2

A1

4,1 4,2 4,3 4,4 4,5 4,6

A2

A1

3,1 3,2 3,3 3,4 3,5 3,6

A2

A1

2,1 2,2 2,3 2,4 2,5 2,6

1,1 1,2 1,3 1,4 1,5 1,6

Figure 4-2 Dual Simultaneous Recipe Requirement

ForteMAXDispensingSystemAddendum Recipe Creation

4.4.1.1 Creating the Recipe

To create the recipe:

1. Make sure the Canvas dispensing software is configured for dual applicators. Both

applicators must be the same.

2. Select the Recipe button to access the Recipe Editor.

3. Place the substrate on the conveyor.

4. Click on the Load button on the toolbar.

> The substrate will be lifted off the conveyor and clamped into place. The substrate

should be evenly clamped and level so that the board does not move when

programming.

5. Adjust the clamping mechanism as necessary to achieve a level dispensing plane.

?

NOTE

The dispensing sequence MUST be taught with the part raised and clamped as

necessary. Failing to load the substrate in this manner results in the camera

being out of focus.

6. Select Recipe > New from the menu bar.

7. Enter the recipe name and click on OK.

8. When prompted, teach the workpiece origin.

9. Select First Fid Location is origin (Figure 4-3).

Figure 4-3 Set Workpiece Origin

10. Click on Next.

> You will be prompted to set the fiducial properties and teach fiducials.

> In this example, two fiducials will be used (Figure 4-4).

11. Follow the prompts to define two circle finder fiducials. Refer to the Canvas Dispensing

Software User Guide if necessary.

12. Click on Done when finished.

1 2 3 4 5 6 7 8 9 10 11 12

2

1

6130139 REV 1

STRAIGHT

B,1

B,2

2,1 2,2 2,3 2,4 2,5 2,6

1,1 1,2 1,3 1,4 1,5 1,6

4,1 4,2 4,3 4,4 4,5 4,6

A2

A1

3,1 3,2 3,3 3,4 3,5 3,6

A2

A1

4

3

4,1 4,2 4,3 4,4 4,5 4,6

A2

A1

3,1 3,2 3,3 3,4 3,5 3,6

A2

A1

2,1 2,2 2,3 2,4 2,5 2,6

1,1 1,2 1,3 1,4 1,5 1,6

Figure 4-4 Workpiece Origin and Workpiece Fiducials

W

o

r

k

p

i

e

c

e

O

r

i

g

i

n

and Workpiece

F

i

d

u

c

i

a

l

1

W

o

r

k

p

i

e

c

e

F

i

d

u

c

i

a

l

2

ForteMAXDispensingSystemAddendum Recipe Creation

4.4.1.2 Creating the Pattern

In this section, we will create a pattern that will dispense four (4) lines around each cell.

To create a pattern:

1. Select the Workpiece pattern in the Recipe Tree and click on Create Pattern in the

Instruction Panel (Figure 4-5).

> You will be prompted to enter a pattern name.

Figure 4-5 Create a Pattern

2. Enter a Pattern Name and click on Next (Figure 4-6).

> In this example, the pattern name will be "1-Square."

Figure 4-6 Set Pattern Name

3. Click on Next.

> You will be prompted to teach the pattern origin.

4. Select First Fid Location is Origin (Figure 4-7).

Figure 4-7 Set Pattern Origin

5. Click on Next.

> You will be prompted to define the fiducials.