Forte Max Manual.pdf - 第46页

ForteMAXDispensingSystemAddendum Recipe Creation

4. Adjust the clamping mechanism as necessary to achieve a level dispensing plane.

?

NOTE

The dispensing sequence MUST be taught with the part raised and clamped as

necessary. Failing to load the substrate in this manner results in the camera

being out of focus.

5. Select Recipe > New from the menu bar.

6. Enter the recipe name and click on OK.

7. When prompted, teach the workpiece origin.

8. Select First Fid Location is Origin (Figure 4-31).

Figure 4-31 Set Workpiece Origin

9. Click on Next.

> You will be prompted to set the fiducial properties and teach fiducials.

> In this example, two fiducials will be used (Figure 4-32).

10. Follow the prompts to define two circle fiducials. Refer to the Canvas Dispensing Software

User Guide if necessary.

11. Click on Done when finished.

1 2 3 4 5 6 7 8 9 10 11 12

2

1

6130139 REV 1

STRAIGHT

B,1

B,2

2,1 2,2 2,3 2,4 2,5 2,6

1,1 1,2 1,3 1,4 1,5 1,6

4,1 4,2 4,3 4,4 4,5 4,6

A2

A1

3,1 3,2 3,3 3,4 3,5 3,6

A2

A1

4

3

4,1 4,2 4,3 4,4 4,5 4,6

A2

A1

3,1 3,2 3,3 3,4 3,5 3,6

A2

A1

2,1 2,2 2,3 2,4 2,5 2,6

1,1 1,2 1,3 1,4 1,5 1,6

Figure 4-32 Workpiece Origin and Workpiece Fiducials

W

o

r

k

p

i

e

c

e

O

r

i

g

i

n

and Workpiece

F

i

d

u

c

i

a

l

1

W

o

r

k

p

i

e

c

e

F

i

d

u

c

i

a

l

2

ForteMAXDispensingSystemAddendum Recipe Creation

4.5.1.1 Creating the Pattern

In this section, we will create a pattern that will dispense four (4) lines around each cell and nine (9) dots

into each cell.

To create pattern:

1. Select the Workpiece pattern in the Recipe Tree

and click on Create Pattern in the Instruction

Panel (Figure 4-33).

> You will be prompted to enter a pattern name.

2. Enter a pattern name and click on Next.

> In this example the pattern name will be

"1-Square" (Figure 4-34).

Fig

ure

4

-

33

C

r

e

a

t

e

a

P

a

t

e

r

n

Figure 4-34 Set Pattern Name

3. Click on Next.

> You will be prompted to teach the pattern origin.

4. Select First Fid Location is Origin (Figure 4-35).

Figure 4-35 Set Pattern Origin

5. Click on Next.

> You will be prompted to define the fiducials.

6. Define the pattern fiducials. In this example, it is recommended to use two corner fiducials

(Figure 4-36). Refer to the Canvas Dispensing Software User Guide if necessary.

1,1 1,2 1,3 1.4 1.5 1,6

2,1 2,2 2,3 2.4 2.5 2,6

Figure 4-36 Pattern Origin and Fiducial Locations

7. Click on Done when finished.

P

a

t

e

r

n

O

r

i

g

i

n

and Pattern

F

i

d

u

c

i

a

l

1

P

a

t

e

r

n

F

i

d

u

c

i

a

l

2

ForteMAXDispensingSystemAddendum Recipe Creation

4.5.1.2 Adding Dispense Instructions

In this example, we will define five (5) line nodes to surround one box and nine dots inside the box. We

will also add pass blocks.

To add the line:

1. Make sure the pattern you created is selected in the Recipe Tree.

2. Select Line from the Instruction Panel.

> The Line Instruction Wizard opens (Figure 4-37).

3. Jog the camera crosshairs to the first line point and click Add.

4. Repeat Step 3 until all the nodes have been defined.

5. Click on Next.

> You will be prompted to set the line properties.

Figure 4-37 Line Instruction Wizard – Set Node Properties

6. Select the Applicator, Line Type, Dispense Strategy and Weight Control (Figure 4-38).

> Refer to the Canvas Dispensing Software User Guide if necessary.

?

NOTE

You must select which applicator will dispense. In this case, Applicator 1 will

dispense the lines.

Figure 4-38 Line Instruction Wizard – Set Line Properties