Tracker-2800-2800S.pdf - 第7页
7 ( - 50 degrees C to +60 degrees C) Humidity 0 to 50% R.H. Dimensions 11.1" W x 4.4" H x 8.5” D (28.2cm W x 11.2cm H x 22.1cm D ) Warrant y 1 year limited Supplied Accessories Huntron P/N QTY Description 06-52…
6
ASA may be universally applied to any type of passive component like a resistor, capacitor, or
inductor, or a solid state semiconductor component like a diode, transistor, SCR, digital, analog, or
mixed-signal IC. When troubleshooting a circuit card, the resultant signature is a composite of various
component signatures at a particular node in the circuitry. By understanding what different signatures
mean, you can determine which components are faulty.
You can manually connect the Tracker 2800 front panel test terminals directly to the circuit card or
component that you are testing. You can automate the test process to a certain degree by connecting to
boards under test via custom cabling or IC clip cables using a Tracker 2800S. The Tracker 2800S is a
modified version of the Tracker 2800 that has internal switch cards and external, front panel IDC
connectors to which custom cable interfaces or DIP clip cables can be connected.
1-2 Specifications
Electrical (Note: Test Signal is a sine wave.) Specifications subject to change without
notice
Open Circuit Voltage (Vs):
6
selections of peak voltage:
200mV,
3V, 5V, 10V, 15V, 20V
Source Resistance (Rs):
9
selections of resistance:
10Ω, 50Ω, 100Ω, 500Ω, 1kΩ, 5kΩ, 10kΩ,
50kΩ, 100kΩ
Short circuit current (Vs divided by Rs)
Maximum
200 mApk
Frequency (fs):
6
selections of frequency:
20Hz
, 50Hz, 60Hz,
200Hz, 500Hz, 2kHz
Channels
Number
2
Connections
Banana (Channel A, Common, Channel B);
Two (Ch. A and Ch. B) 40 pin IDC connectors (Tracker
2800S only)
Overvoltage Protection
Circuit breaker
Auxiliary Connection
9 pin mini jack with ground, Trigger IN, Trigger OUT,
Calibration TP, Sine wave zero-crossing, Signal ON, Line
IN and Line OUT
DC Voltage Source
0
-
10VDC + output @ 200mA max;
PC Interface
USB 2.0
GENERAL
Power Requirements
100/115V~ 0.2A 50/60Hz, 230V~ 0.1A 50Hz
Fuse
T400mA 5x20mm 250V
Operating Temperature
59 degrees F to 86 degrees F
(+15 degrees C to +30 degrees C)
Storage Temperature
-
58 degrees F to 140 degrees F
7
(
-
50 degrees C to +60 degrees C)
Humidity
0 to 50%
R.H.
Dimensions
11.1" W x 4.4" H x 8.5” D (28.2cm W x 11.2cm H x
22.1cm D
)
Warranty
1 year limited
Supplied Accessories
Huntron P/N QTY Description
06-5217 1 User's Manual CD
98-0043 2 Test Lead Black
98-0249 1 pair Huntron Microprobes MP20
98-0265 1 Power cord
98-0284 1 Shrouded blue test lead
1-3 Safety Information (Information sur la sécurité )
Symbols and Warnings: (Symboles et avertissements):
The following symbols are used either in this manual or on the unit:
Les symboles suivants sont utilisés soit dans ce manuel ou sur l'appareil:
Protective Ground (Earth) Terminal. Do not disconnect any protective ground
wires.
Rez de protection (terre). Ne débranchez pas de câbles de garde protectie.
CAUTION This symbol is used in the user’s manual as a warning that improper use could
result in unit malfunctioning. For your safety always follow the instructions next to the
symbol on the unit and in the manual.
ATTENTION Ce symbole est utilisé dans le manuel de l'utilisateur comme un avertissement que
l'usage abusif peut entraîner des dysfonctionnements unité. Pour votre sécurité toujours suivre les
instructions à côté du symbole de l'unité et dans le manuel.
The Huntron Tracker 2800 conforms to the following Standards:
8
EN/IEC 55011
EN 61000-3-2
EN 61000-3-3
EN/IEC 61000-4-2
EN/IEC 61000-4-3
EN/IEC 61000-4-4
EN/IEC 61000-4-5
EN/IEC 61000-4-6
EN/IEC 61000-4-8
EN/IEC 61000-4-11
IEC 61010-1:2010 (Third Edition)
UL 61010-1 Issued: 2012/05/11 Ed:3
CSA C22.2 No. 61010-1 Issued:2012/05/11 Ed:3
EN 61326-1: 2013
IEC 61326-1: 2012
Meets the Standard for Safety Requirements for Electrical Equipment for Measurement,
Control and Laboratory Use; Part 1 General Requirements – UL 61010-1, 2
nd
Ed., with revisions
through 07/22/2005, and CAN/CSA-C22.2 No. 61010-1, 2
nd
Ed., dated 07/12/2004.
Line Fuse Replacement: (Line Remplacement des fusibles):
Line Fuse tray: The power entry module includes a power cord connector, and a removable tray
which holds the line fuses.
Ligne bac Fuse: Le module d'entrée comprend un connecteur d'alimentation cordon d'alimentation, et
un plateau amovible qui contient les fusibles en ligne.
Make sure that replacement fuses are of the type and current rating specified. If necessary, insert a
T400mA 5x20mm 250V fuse into the fuse tray.
Assurez-vous que les fusibles de remplacement sont de type et leur courant nominal spécifié. Si
nécessaire, ajouter un 5x20mm T400mA 250V dans le bac à fusibles.
Do Not Operate Without Covers. Do not operate this instrument with covers or panels removed.
Ne pas fonctionner sans Covers. Ne pas utiliser cet instrument avec ou panneaux enlevés.
Avoid Exposed Circuitry. Do not touch exposed connections and components when power is present.
Évitez les circuits à découvert. Ne touchez pas les exposés et les composants lorsque la puissance
est présente.
Do Not Operate With Suspected Failures. If you suspect there is damage to this instrument, have it
inspected by qualified service personnel.
Ne pas utiliser Avec les échecs présumés. Si vous pensez que il ya des dommages à cet instrument, le
faire inspecter par un technicien qualifié.