00197004-04_UM_X-Serie-S_EN.pdf - 第234页

4 Setting up and commissioning User manual SIPLACE X-Series 4.2 Infrastructure at the installation location From software ve rsion 706.1 SP1 Version 10/2014 234 4.2.3.2 Checking the main power supply Check whether the p …

User manual SIPLACE X-Series 4 Setting up and commissioning

From software version 706.1 SP1 Version 10/2014 4.2 Infrastructure at the installation location

233

4.2.3 Main power supply

Fig. 4.2 - 2 Position of power supply on the machine (example of SIPLACE X2 S / X3 S / X4 S shown)

(1) Lock

(2) Main power switch secured to prevent switching on again

(3) Power supply unit (behind the cover)

(4) Mains connection cable

4.2.3.1 Danger notes

(1)

(2)

(3)

(4)

DANGER

Dangerous voltage levels!

The machine is supplied with 3 x 200 V~, 3 x 208 V~, 3 x 220 V~, 3 x 230 V~,

3 x 380 V~, 3 x 400 V~ or 3 x 415 V~ ± 5 %, 50/60 Hz mains voltage. This means that

some parts of the system carry potentially lethal voltages - even when switched off at the

main power switch.

Incorrect handling of this machine can therefore result in death or severe injury or con-

siderable damage to equipment.

 Always follow the applicable accident prevention and DIN regulations (particularly

EN 60204, part 1 or IEC 60204, part 1) and the applicable regulations in your own

country.

 The covers over the power supply unit may ONLY be opened by appropriately qual-

ified and trained personnel.

4 Setting up and commissioning User manual SIPLACE X-Series

4.2 Infrastructure at the installation location From software version 706.1 SP1 Version 10/2014

234

4.2.3.2 Checking the main power supply

Check whether the power supply complies with the prescribed machine specifications (see table

in section 3.2

, page 121).

4.2.3.3 Power supply cable - specification

The following specifications apply at the customer end to the power supply for the machine:

– 5 x 2.5 mm² at 3 x 380 V~ / 3 x 400 V~ / 3 x 415 V~ at cable lengths of up to 20 meters be-

tween placement machine distribution and mains connection at the customer end. Over 20

meters cable 5 x 4 mm².

– 5 x 4 mm² at 3 x 200 V~/ 3 x 208 V~ / 3 x 220 V~ / 3 x 230 V~ at cable lengths of up to 20

meters between placement machine distribution and mains connection at the customer end.

Over 20 meters cable 5 x 6 mm².

The color coding for the wires will depend on the country in which the system is operated.

PLEASE NOTE

Load peaks in power supply

For technical reasons, load peaks occur in the power supply.

 Please contact your power company to clarify the mains impedance, if necessary.

WARNING

Clear marking of electrical leads!

The electrical leads to each individual machine and to the options installed must be clear-

ly labeled and easily assignable.

 The regulations of the country in which the machine is operated apply.

User manual SIPLACE X-Series 4 Setting up and commissioning

From software version 706.1 SP1 Version 10/2014 4.2 Infrastructure at the installation location

235

4.2.3.4 Mains connection - delivery configuration

The main power connection is configured according to the power supply of the country concerned.

– The machine is configured for voltages of 200V AC, 220V AC or 230V AC.

The machine has a mains power cable WITHOUT plug. 4

Fig. 4.2 - 3 Description of wires in the mains power cable

– The machine is configured for voltages of 380V AC, 400V AC or 415V AC.

The machine has a mains power cable WITH Cekon plug. 4

Fig. 4.2 - 4 Assignment in the Cekon plug

1 = (L1): three-phase

2 = (L2): three-phase

3 = (L3): three-phase

4 = (N): neutral conductor

green/yellow = (PE): conductor