00192662-01.pdf - 第200页
5 Single Functions User Manual SIPLACE F5/F5 HM 5.2 Single functions, Gantry Software version SR.407.x x 01/2001 US E dition 200 5.2.7 "Nozzle change r configuration revolv er head" scree n for 6-noz zle C&…
User Manual SIPLACE F5/F5 HM 5 Single Functions
Software version SR.407.xx 01/2001 US Edition 5.2 Single functions, Gantry
199
Confirm 5
This function allows you to confirm that a nozzle has been changed (without nozzle changer).
To change a nozzle without a nozzle changer you must perform the operation by hand. You can
only change the nozzle on one segment at a time because the segment must be in the
changeover position. By turning the head in a clockwise fashion you can bring each segment in
turn to the changeover position.
5
Å In the table, find the segment for which the nozzle is to be changed.
Å Click the RV head indexing button as often as required to bring the required segment round
until it is displayed in the changeover position (marked with an arrow).
The table entry for this segment is now highlighted in light blue (see Fig. 5.2 - 9
).
Å Remove the nozzle by hand and replace it with a nozzle of the type shown in the "Preset" col-
umn.
Å Click the Confirm button.
The change is confirmed. The entries in the columns "Actual" and "Preset" agree. The new
nozzle configuration is saved to the machine data.
5 Single Functions User Manual SIPLACE F5/F5 HM
5.2 Single functions, Gantry Software version SR.407.xx 01/2001 US Edition
200
5.2.7 "Nozzle changer configuration revolver head" screen for 6-nozzle C&P head
5
Å In the current screen for the single function for Gantry, click the symbol .
NOTE
The nozzle changer must be installed and configured in the machine options. When calling
this scrren the nozzles on the placement head are returned to the nozzle changer. 5
The user interface is switched to the "Nozzle changer configuration revolver head" screen (see
Fig. 5.2 - 11
). 5
5
Fig. 5.2 - 11 "Nozzle changer configuration revolver head" screen (6--nozzle Collect&Place head)
User Manual SIPLACE F5/F5 HM 5 Single Functions
Software version SR.407.xx 01/2001 US Edition 5.2 Single functions, Gantry
201
5.2.7.1 General comments
In the "Nozzle changer configuration revolver head" screen there are functions which allow you to
adjust and confirm the nozzle configuration for the individual magazines in the nozzle changer.
Click on the appropriate button to carry out the required function.
The nozzle changer configuration is displayed in the table in the display.
5
Conditions for changing the set-up of the nozzle changer
Remember the following points when changing the set-up: 5
– The magazines may only be filled when all nozzles on the Collect&Place head have been re-
turned to their magazines.
– The magazines for type 7xx or 8xx nozzles are different.
– Only nozzles of type 7xx or 8xx can be set up in a single magazine. They must not be mixed.
– The maximum number of nozzles per magazine is 6.
– The maximum number of magazines on a nozzle changer is 5.
– The magazines must be filled outside the machine and must only ever be changed in their en-
tirety.
– To remove and load nozzles you must open the lock. Once you have finished, you must then
close the lock again.
Meaning of the entries in the table in the display
– Magazine
Number of the magazine
– Garage
Number of the nozzle holder
– Number
Number of nozzles in the magazine
– Actual
Type of nozzles currently in the magazine
– Preset
If the type of nozzle currently in the magazine is not the same as shown in this column, then it
is to be changed
– To change
An arrow ( <== ) in this column indicates that the nozzle type currently in the magazine
("Actual" column) must be changed for the nozzle type shown in the "Preset" column.