DFD6361-Maintenance.pdf - 第474页
E-38 1-3-4. Com pletion of spindl e clea ning Procedur e for completi on of spindle cle aning CAUTION After cle aning the spi ndle, dry it co mpletely . Moisture or drops of water left on it can lea d to corrosi on of th…
E-37
1-3-3. Cleaning the spindle main body
Procedure for cleaning the spindle main body
CAUTION
- Be careful not to touch the edge of the spindle. If your fingers or
hands touch it, you may be injured.
- Do not use the scrubbing cloth to clean the taper section. Such
cloth scratches the surface of the taper section, which deteriorates
its accuracy.
Step No.
Do This
(Continued from the previous section)
1
With wastes, clean the thrust bearing section and air curtain outlet.
With the lint-free cloth moistened with alcohol, wipe off soil on
the spindle front rid, air outlet and seal ring.
Spindle front rid
Air outlet
Taper section
Seal ring
: Cleaning area
2
Make sure that air is discharged from all round the air outlet.
3
If the air outlet is blocked with soil;
With a soft nylon brush such as toothbrush, rake out soil of the air
outlet. And then, perform the step procedures of No. 1 and 2.
Continued in the next section.
E-38
1-3-4. Completion of spindle cleaning
Procedure for completion of spindle cleaning
CAUTION
After cleaning the spindle, dry it completely. Moisture or drops of
water left on it can lead to corrosion of the spindle.
Step No.
Do This
(Continued from the previous section)
1
Wash out stains.
2
Wipe out drops of water on the spindle with clean wastes.
3
Blow air to the spindle in order to dry it.
4
If you removed the wheel cover,
- Reinstall the wheel cover piping.
- Reinstall the wheel cover.
5
Reinstall the flange or hub mount.
6
Install the blade.
FYI: Possible problems of the spindle due to stains
Generation of rust
Although the anti-corrosion stainless steel is used as the material of the spindle,
there is a possibility that rust will form on the spindle, depending on the usage
conditions, which might ultimately result in breakage of the spindle.
Generation of abnormal sound
If contamination adheres to around the outlet of air curtain, wind noise could
be emitted.
Motor failure and galling of the ball bearing section
If the air curtain function is deteriorated, the wheel coolant water will enter
inside the spindle and this could cause failure of the motor.
Also, the degraded function of the ball bearing section could result in galling.
E-39
1-4. Cleaning the Touch Panel
Safety items for cleaning the touch panel
WARNING
- If a foreign matter (small piece of metal, water or other liquid) gets
into the touch panel, immediately turn OFF the machine, shut off
the facility power source and then contact Disco. If you continue to
use the touch panel leaving it as it is, a fire, an electric shock or a
breakdown could occur.
- Do not press the touch panel display with a sharp tipped thing such
as a mechanical pencil and driver or a rigid thing, or with strong
force. If you do so, the touch panel could be broken.
If the panel display is damaged and crystal liquid inside adheres to
skin, immediately rinse it under running water for more than 15
minutes.
If crystal liquid gets in eyes or mouth, immediately rinse it under
running water for more than 15 minutes and then consult your
doctor.
CAUTION
When the touch panel display gets dirty, moisten a dry soft cloth with
a neutral detergent and wring well water out of the cloth, and then
wipe the display surface out.
Do not use any organic solvent other than ethanol for cleaning. An
organic solvent may cause a deterioration or discoloring.
NOTICE
Neither safety goggles, protective gloves, stepstools, flashlights nor
alcohol, all of which are necessary for maintenance work, are not
supplied with the machine. Use what are furnished in your factory or
what comply with your factory's standards.
Before cleaning
Have on hand the following items for cleaning the touch panel.
Dry soft cloth
Neutral detergent
Ethyl alcohol (For stubborn stains)