Infinity EX Transportation.pdf - 第42页

INFINITY EX TRANSPORT ATION MAJOR RE LOCATION 31.4 2 Technical Reference Manual Chapter Issue 3 Jan 04 face of the auxiliary con ve yor rail. 15. Connect to the following connectors situated on the front auxiliary con ve…

INFINITY

TRANSPORTATION

MAJOR RELOCATION

Chapter Issue 3 Jan 04 Technical Reference Manual 31.41

a. Adjust the right hand auxiliary conveyor rail width to approximately

250mm.

b. Place a Board Clamp Setting Plate Pt No 140403 onto the auxiliary

conveyor transport belts.

c. Place a spirit level on top of the setting plate and check the levelness of

the conveyor in the X and Y planes.

d. If adjustment is required, carry out Steps 13e - 13g.

e. Loosen the four bolts that secure the auxiliary conveyor shaft guide plate

to the rear rail support and the four bolts that secure the rail bracket to front

rail support.

f. Carefully adjust the height of the auxiliary conveyor rails to achieve

conveyor levelness in the X and Y planes.

g. Re-tighten the rail bracket and shaft guide plate securing bolts and repeat

the check.

14.Connect M27PL17 connector to the rear transport belt motor fitted to the rear

Board Clamp

Setting Plate

View on Auxiliary Conveyor

Spirit Level

Rear View of Right Auxiliary Conveyor

Front Auxiliary Conveyor

Rail Support

Rear Auxiliary Conveyor

Rail Support

Shaft Guide Plate

Shaft Guide Plate to Rear

Rail Support Bolts (4 off)

Rail Bracket to Front

Rail Support Bolts

(in 4 positions)

INFINITY

TRANSPORTATION

MAJOR RELOCATION

31.42 Technical Reference Manual Chapter Issue 3 Jan 04

face of the auxiliary conveyor rail.

15.Connect to the following connectors situated on the front auxiliary conveyor

rail:

• M27SK14 - Auxiliary conveyor sensor

• M27PL16 - Auxiliary conveyor front transport belt motor

16.Connect the electrical supply connectors to the pneumatic solenoid valves

M27SOL01 and M27SOL03 situated on the rear face of the front rail

support.

17.Connect solenoid valves M27SOL01and M27SOL03 with the 4mm pneum-

tic pipe at the tee piece connection to valve M27SOL03.

18.Refit the right hand machine side covers removed in Step10.

19.The following auxiliary conveyor checks are to be carried out:

• Auxiliary Conveyor Rail Parallelism

• Auxiliary Conveyor Height Setting

These checks require power to be available to the machine and are detailed

later in this chapter.

Fitting of Machine

Safety Covers (HTC

Option)

To fit the machine safety covers carry out the following:

1. Attach a safety plate to the top of each pair of auxiliary conveyor rails using

Connector M27PL17

Rear View on Right Auxiliary Conveyor

Front View on Right Hand Auxiliary Conveyor

Connector M27SK14

Connector M27PL16

INFINITY

TRANSPORTATION

MAJOR RELOCATION

Chapter Issue 3 Jan 04 Technical Reference Manual 31.43

two M5 countersunk screws and nylon spacers. Ensure the spacers are fitted

between the safety plate and the top of the rail.

2. Ensure spacers are fitted to each auxiliary conveyor rear support.

3. Fit the machine safety covers to each side of the machine ensuring the cover

fits over the safety plate preventing it from rising.

External Services In order for the machine to function correctly the following services must be

available. The services must be stable and clean.

Pneumatic Supply The machine requires a pneumatic supply of clean, non lubricated air which

should maintain a minimum pressure 5 Bar and a maximum of 8 Bar.

The air should be to ISO 8573.1 standard, quality class 2.3.3, where:

• 2 dirt = 1 micron

• 3 water = -20°C pressure dewpoint

• 3 oil = 1mg/m

Electrical Supply The average power consumption for a machine without any options fitted is

2KVA at 100/240Vac 50/60Hz.

DEK recommends a power supply capacity of 3KVA or greater to accommodate

extra options, surges on power-up and certain machine operations.

CAUTION

OVER CURRENT PROTECTION. Magnetic/thermal over current pro-

tectors protect the machines internal wiring and components from over-

heating/fire during fault conditions. DEK require additional machine

supply protection with the fitment of a wall mounted circuit breaker rated

to 16 Amps and conforming to national/federal regulations.

Safety Cover

(in 2 positions)

Safety Plate

M5 Countersunk Screw

With Spacer (in 2 positions)

Internal View of Right hand Side of Machine