Infinity EX Transportation.pdf - 第6页
INFINITY EX TRANSPORT ATION MINOR RELO CATION 31.6 Technical Reference Manu al Chapter Is sue 3 Jan 04 T ransit Bracket Rem oval CAUTION SCREEN ACTUATOR BRA CKETS. Extr eme care must be taken when installing or r emovi n…
INFINITY
EX
TRANSPORTATION
MINOR RELOCATION
Chapter Issue 3 Jan 04 Technical Reference Manual 31.5
Transportation
WARNING
MACHINE LIFTING. TO PREVENT SERIOUS INJURY TO
PERSONNEL, DURING LIFTING AND TRANSPORTATION
OPERATIONS, ENSURE THE MACHINE IS LIFTED AND
TRANSPORTED IN ACCORDANCE WITH INSTRUCTIONS
DETAILED IN THIS SECTION.
CAUTION
MACHINE DAMAGE. Damage to the machine will occur if the machine
is lifted:
• Using lifting strops
• From the sides
The machine may be lifted using a pallet trolley or similar manually operated
machine that meets the following criteria:
• Has two 48 inch long forks
• The forks have a 27 inch span
• Has a lifting capability of 2000kg
1. Locate the forks under the machine base so the weight of the machine is
taken evenly on the front and rear cross members.
NOTE
Height of machine feet may have to be adjusted to allow the pallet trolley to
raise the machine clear of the floor.
2. Raise the machine and carefully transport into position.
Figure 31-3 Machine on Pallet Truck
INFINITY
EX
TRANSPORTATION
MINOR RELOCATION
31.6 Technical Reference Manual Chapter Issue 3 Jan 04
Transit Bracket
Removal
CAUTION
SCREEN ACTUATOR BRACKETS. Extreme care must be taken when
installing or removing the screen actuator brackets as the chase is spring
loaded against the screen actuator ends in the X Forward, X Rear and Y
Axis Positions. Impact force may damage the actuators.
1. On the two X axis chase restrainer brackets (X and Y Chase Restrainer
Brackets figure refers), release the locknuts by turning them in an anti-
clockwise direction. Slowly turn the black hand wheels in an anti-clockwise
direction until the actuators have made contact with the chase striker plates.
Continue to turn the hand wheels until the threads have withdrawn enough
to allow access to the lower cap head screws.
2. On the Y axis chase restrainer bracket (X and Y Chase Restrainer Brackets
figure refers), release the locknut. Slowly undo the cap head screw until the
actuator has made contact with the chase striker plate. Continue to undo the
cap head screw until the bracket can be easily removed from the Y axis
actuator.
On completion of relocation, carry out the following:
1. Reconnect electrical power supplies.
2. Reconnect pneumatic supplies.
INFINITY
EX
TRANSPORTATION
MAJOR RELOCATION
Chapter Issue 3 Jan 04 Technical Reference Manual 31.7
MAJOR RELOCATION
Introduction This procedure is to be utilized when the machine is being relocated on the
following occasions:
• Machine relocation to another site outside the original factory.
• If the machine has to experience any substantive shocks or vibration.
Machine
Preparations
Prior to a major relocation it is recommended the following is carried out:
• Machine capability check (see Machine Performance).
• Check the shock watches are in position (Figure Shock Watch Locations
refers) and untriggered (displays a red arrow). To reset units use a pin
through the access hole.
Installation
Procedure
Prior to installing transit brackets to the machine ensure the following:
CAUTION
SCREEN ACTUATOR BRACKETS. Extreme care must be taken when
installing or removing the screen actuator brackets as the chase is spring
loaded against the screen actuator ends in the X Forward, X Rear and Y
Axis Positions. Impact force may damage the actuators.
1. With power applied to the machine:
a. Home the moving rail.
b. Home the X and Y screen actuators.
c. Home the paste dispenser (if fitted).
2. Remove the squeegee drip tray.
3. Remove the under screen cleaner.
NOTE
If required, raise printhead for access when removing underscreen cleaner.
Front Transit
Bracket
NOTE
For guidance, when fitting the front transit bracket, refer to the following figures:
• Transit Brackets Machine Location
• Front Transit Bracket and Camera Transit Bracket (with table)
• Front Transit Bracket Stud Locations
1. Check that the camera transit bracket is fitted to the main transit bracket, ie
on the left hand stud of the printhead lift stud. Check that all nuts and
washers are fitted to all the bracket studs.
2. With power still applied to the machine, jog the print carriage forward until
the front and rear squeegee mounts are over the squeegee mount support
bracket (Item 1e).
3. Switch OFF and disconnect the machine electrical power.
4. Disconnect the air supply.
5. Lightly grease the four chase rollers.
6. Position the front transit bracket across the print carriage guide rails.