instruction-manual-product-monitoring-data-acquisition-monitouch-V9-hardware-en.pdf - 第34页
2 1. Advanced Model 2-3 Specifications T ouch Switch Specifications Wireless LAN Specificat ions (Only for Wireless LAN I/F Models) * For details of other wireless LAN specifications, refer to page 3-22. Item V9101iW V91…
2-2 1. Advanced Model
*2 Use the unit in an environment where the wet-bulb temperature is 39 C or less, otherwise the unit may be
damaged.
*3 This indicates the distribution section to which the unit is intended to be connected to within the path between
the distribution of the public power network and machinery in the facility.
“Category II” applies to devices supplied with power from mains sockets or similar points. The withstand surge
voltage is 2,500 V for devices rated up to 300 V.
*4 This is an index that expresses the degree of conductive contamination in the environment where the unit is
used.
“Contamination level 2” indicates the conditions where only non-conductive contamination occurs. However,
due to condensation, temporary conductive contamination may occur.
Installation Specifications
*1 Protective structure for the front when the V9 series unit is mounted on a mounting panel.
While the protective structure has passed compliance testing, it is not guaranteed under all environments.
*2 Applies to V910xiW from hardware version c and later.
*3 Even when the mounting panel thickness is within the specified range, the panel itself may warp depending on
the material and size of the mounting panel.
Use a panel that can withstand the forces of mounting.
Display Specifications
*1 Only for displaying “picture” images, 3D parts and video images. All other content is displayed using 65,536
colors.
*2 Time until the surface brightness becomes 50 % of the initial value at an ambient temperature of 25 C.
Item Specification
Grounding Less than 100 , FG/SG separated
Protection Structure
Panel Front Surface
*1
Complies with IP66, Type 4X/13
*2
(when waterproof gasket is installed)
Rear Case Complies with IP20
Cooling System Natural cooling
Structure Inserted in a mounting panel
Appropriate Mounting Panel Thickness
1.5 to 4 mm
*3
Item V9101iW V9100iW V9071iW V9070iW
Display Device TFT color
Display Size 10.1-inch widescreen 7.0-inch widescreen
Colors
16.77 million colors
*1
Resolution (W H) 1024 600 dots 800 480 dots
Dot Pitch (W H) 0.2175 0.2088 mm 0.1905 0.1905 mm
Actual Display Dimensions
(W H)
222.72 125.28 mm 152.4 91.44 mm
Backlight LED
Backlight Brightness
Halftime
*2
Approx. 50,000 hours Approx. 100,000 hours
Backlight Auto OFF Function Always ON, custom setting
Brightness Adjustment
System menu: 16 levels
Macro: 128 levels
Touch Panel Operation
Surface
Touch panel
(Glass)
Surface sheet
(PET, 0.188 mm)
Touch panel
(Glass)
Surface sheet
(PET, 0.188 mm)
POWER Lamp
On: Normal (green)
Flashing: Circuit board or power supply failure
2
1. Advanced Model 2-3
Specifications
Touch Switch Specifications
Wireless LAN Specifications (Only for Wireless LAN I/F Models)
* For details of other wireless LAN specifications, refer to page 3-22.
Item V9101iW V9100iW V9071iW V9070iW
Type
Projected-capacitive
type
Analog resistive film
type
Projected-capacitive
type
Analog resistive film
type
Switch Resolution - 1024 1024 - 1024 1024
Mechanical Life -
One million
activations or more
-
One million
activations or more
Surface Treatment Clear Anti-glare treatment Clear Anti-glare treatment
Item Specification
Complying Antennas
Built-in antenna of the V9 series unit
V9-ANT (optional): External dipole antenna for wireless LAN
2-4 1. Advanced Model
Interface Specifications
*1 For the V907xiW, the optional “DUR-00” unit (PPI/MPI connection with a Siemens PLC is invalid) must be
attached.
*2 For details, refer to the V9 Series Connection Manual 1.
*3 Only for V910xiW.
*4 Only for V907xiW.
*5 Both straight and cross cables are usable, irrespective of the presence or absence of a hub.
*6 Only for wireless LAN I/F models.
Item Specification
D-sub 9-pin (CN1)
*1
Applicable
standards
RS-232C, RS-485 (2-wire connection), RS-422 (4-wire connection)
Synchronization Asynchronous type
Data Length 7 or 8 bits
Parity None, even, odd
Stop Bit 1 or 2 bits
Baud Rate
4800, 9600, 19200, 38400, 57600, 76800, 115k bps
(For PPI/MPI connection with a Siemens PLC: 187.5 kbps
*2 *3
)
Applications PLC, temperature controller, barcode reader connection, etc.
Modular Jack, 8-pin
(MJ1, MJ2
*3
)
Applicable
standards
RS-232C, RS-485 (2-wire connection)
Baud Rate 4800, 9600, 19200, 38400, 57600, 76800, 115k bps
Applications
Screen program transfer (MJ1), PLC, temperature controller, barcode reader,
printer, multi-link2, V-Link connection, etc.
Modular Jack, 8-pin
(MJ2
*4
)
Applicable
standards
RS-232C, RS-485 (2-wire connection), RS-422 (4-wire connection)
Baud Rate
4800, 9600, 19200, 38400, 57600, 76800, 115k bps
(For PPI/MPI connection with a Siemens PLC: 187.5 kbps
*2
)
Applications PLC, temperature controller, barcode reader connection, etc.
USB Connector
(U-A, U-B)
USB-A
Applicable
standards
Compliant with USB version 2.0
Baud Rate High speed 480 Mbps
Applications
Printer (EPSON ESC/P-R driver), USB flash drive, keyboard, mouse connection,
etc.
USB mini-B
Applicable
standards
Compliant with USB version 2.0
Baud Rate High speed 480 Mbps
Applications Screen program transfer, PictBridge-compatible printer connection
Ethernet Port
100BASE-TX /
10BASE-T
(LAN, LAN2)
Applicable
standards
IEEE802.3u compliant (100BASE-TX), IEEE802.3 compliant (10BASE-T)
Baud Rate 100 Mbps, 10 Mbps
Protocol TCP/IP, UDP/IP
Functions Auto-MDIX, Auto-Negotiation
Recommended
Cable
*5
100 UTP (unshielded twist-pair) cable, category 5, max. 100 m long
Applications Screen program transfer, PLC connection, etc.
Connector for Wireless LAN Dipole
Antenna (WLAN)
*6
Reverse polarity SMA jack
SD Card Interface SD/SDHC card compliant
Communication Interface Unit Connector
(EXT1)
Optional unit “DUR-00”
*4
and communication interface unit “CUR-xx” (for
SX-BUS, OPCN-1, T-Link, Ethernet, CC-Link, PROFIBUS-DP, DeviceNet, and
FL-net) connection
* The “DUR-00” and “CUR-xx” cannot be used at the same time.
Connector for Optional Unit
(EXT2)
*3
Optional unit “GUR-xx” (for RGB input, RGB output, and video input) connection
Audio Output Connector (AUDIO)
*3
3.5 mm stereo mini jack