instruction-manual-product-monitoring-data-acquisition-monitouch-V9-hardware-en.pdf - 第8页

[General Notes]  Never bundle control cables or input/output cables with high-voltage and large-curre nt carrying cables such as power supply cables. Keep control c ables and input/output cables at least 200 mm away fro…

 Equipment must be correctly mounted so that the main terminal of the V9 series will not be touched

inadvertently. Otherwise, an accident or electric shock may occur.

 Tighten the mounting screw on the fixtures of the V9 series to an equal torque of 5.31 Ibf-in (0.6 N·m).

Excessive tightening may distort the panel surface. Loose mounting screws may cause the unit to fall down,

malfunction, or short-circuit.

 Check periodically that terminal screws on the power supply terminal block and fixtures are firmly tightened.

Loosened screws or nuts may result in fire or malfunction.

 Tighten the terminal screws on the power supply terminal block of the V9 series to an equal torque of 7.1 to

8.8 Ibf-in (0.8 to 1.0 N·m). Improper tightening of screws may result in fire, malfunction, or other serious

trouble.

 The V9 series has a glass screen. Do not drop the unit or impart physical shocks to the unit. Otherwise, the

screen may be damaged.

 Correctly connect cables to the terminals of the V9 series in accordance with the specified voltage and

wattage. Overvoltage, overwattage, or incorrect cable connection could cause fire, malfunction, or damage

to the unit.

 Always ground the V9 series. The FG terminal must be used exclusively for the V9 series with the level of

grounding resistance less than 100 . Otherwise, you may sustain an electric shock, a fire may occur,

MONITOUCH may not recognize touch operations, and malfunctions may occur.

 Prevent any conductive particles from entering the V9 series. Failure to do so may lead to fire, damage, or

malfunction.

 After wiring is finished, remove the paper used as a dust cover before starting operation of the V9 series.

Operation with the dust cover attached may result in accidents, fire, malfunction, or other trouble.

 Do not attempt to repair the V9 series yourself. Contact Hakko Electronics or the designated contractor for

repairs.

 Do not repair, disassemble, or modify the V9 series. Hakko Electronics Co., Ltd. is not responsible for any

damages resulting from repair, disassembly, or modification of the unit that was performed by an

unauthorized person.

 Do not use sharp-pointed tools to press touch switches. Doing so may damage the display unit.

 Only experts are authorized to set up the unit, connect cables, and perform maintenance and inspection.

 Lithium batteries contain combustible material such as lithium and organic solvents. Mishandling may cause

heat, explosion, or ignition resulting in fire or injury. Read the related manuals carefully and correctly handle

the lithium battery as instructed.

 Take safety precautions during operations such as changing settings when the unit is running, forced output,

and starting and stopping the unit. Any misoperations may cause unexpected machine movement, resulting

in machine accidents or damage.

 In facilities where the failure of the V9 series could lead to accidents that threaten human life or other serious

damage, be sure that such facilities are equipped with adequate safeguards.

 When disposing of the V9 series, it must be treated as industrial waste.

 Before touching the V9 series, discharge static electricity from your body by touching grounded metal.

Excessive static electricity may cause malfunction or trouble.

 Insert an SD card into MONITOUCH in the same orientation as pictured on the unit. Failure to do so may

damage the SD card or the slot on the unit.

 The SD card access LED flashes red when the SD card is being accessed. Never remove the SD card or

turn off power to the unit while the LED is flashing. Doing so may destroy the data on the SD card. Check

that th

e LED has turned off before removing the SD card or turning off the power to the unit.

 Be sure to remove the protective sheet that is attached to the touch panel surface at delivery before use.

Using MONITOUCH with the protective sheet attached may result in incorrect touch switch activation.

 When using an analog resistive-film type V9 series unit, do not touch two positions on the screen at the

same time. If two or more positions are pressed at the same time, the switch located between the pressed

positions may be activated.

CAUTION

[General Notes]

 Never bundle control cables or input/output cables with high-voltage and large-current carrying cables such as

power supply cables. Keep control cables and input/output cables at least 200 mm away from high-voltage and

large-current carrying cables. Otherwise, malfunction may occur due to noise.

 When using the V9 series in an environment where a source of high-frequency noise is present, it is

recommended that the FG shielded cable (communication cable) be grounded at each end. However, when

communication is unstable, select between grounding one or both ends, as permitted by the usage

environment.

 Be sure to plug connectors and sockets of the V9 series in the correct orientation. Failure to do so may lead to

damage or malfunction.

 If a LAN cable is inserted into the MJ1 or MJ2 connector, the device on the other end may be damaged. Check

the connector names on the unit and insert cables into the correct connectors.

 Do not use thinners for cleaning because it may discolor the V9 series surface. Use commercially available

alcohol.

 If a data receive error occurs when the V9 series unit and a counterpart unit (PLC, temperature controller, etc.)

are started at the same time, read the manual of the counterpart unit to correctly resolve the error.

 Avoid discharging static electricity on the mounting panel of the V9 series. Static charge can damage the unit

and cause malfunctions. Discharging static electricity on the mounting panel may cause malfunction to occur

due to noise.

 Avoid prolonged display of any fixed pattern. Due to the characteristic of liquid crystal displays, an afterimage

may occur. If prolonged display of a fixed pattern is expected, use the backlight’s auto OFF function.

 The V9 series is identified as a class-A product in industrial environments. In the case of use in a domestic

environment, the unit is likely to cause electromagnetic interference. Preventive measures should thereby be

taken appropriately.

 The signal ground (SG) and frame ground (FG) are connected inside the V9150 series unit. Take care when

designing systems.

[Notes on the LCD]

Note that the following conditions may occur under normal circumstances.

 The response time, brightness, and colors of the V9 series may be affected by the ambient temperature.

 Tiny spots (dark or luminescent) may appear on the display due to the characteristics of liquid crystal.

 There are variations in brightness and color between units.

[Notes on Capacitive Touch Panels]

 Touch panel operability may not be optimal if used with dry fingers or skin. In such a case, use a capacitive

stylus pen.

 Periodically clean the touch panel surface for optimum touch operations.

When cleaning, take note of the following points.

- The panel surface is made of glass. Be sure to clean the surface gently with a cloth or sponge. Otherwise,

you may scratch or damage the glass.

- Take care not to let cleaning detergent to seep into the touch panel unit.

Do not directly apply or spray cleaning detergent on the panel surface.

 When using a V9 series unit of the capacitive type, observe the following points.

- Use a Class 2 power supply for the 24 VDC power unit. Using MONITOUCH with an unstable power

supply may result in incorrect touch switch activation.

- Capacitive touch panel types support t

wo-point touch operations. If a third point is touched, the touch

operation will be cancelled.

- Capacitive touch panel types are prone to the influence of conductive material. Do not place conductive

material such as metals near the touch panel surface and do not use the panel if it is wet. Otherwise,

malfunctions may occur.

CAUTION

[Notes on Wireless LAN]

For details regarding supported wireless LAN standards, radio law certifications, and countries where wireless LAN

can be used, refer to the “About Wireless LAN on V9 Advanced Model”/“About Wireless LAN on V9 Standard

Model” manual or the “V9 Series Hardware Specifications” provided with the V9 series unit at delivery.