instruction-manual-product-monitoring-data-acquisition-monitouch-V9-hardware-en.pdf - 第77页
3-12 2. Specifications of Components 2. Specifications of Components Serial Connector (CN1) This connector is used to connect a controller or barcode reader via RS-232C, or connect a controller via RS-422/485. For the V9…
3
1. Names and Functions of Components 3-11
Names and Specifications of Components
8. USB cable clamp hole
This clamp hole is used to attach a USB cable tie.
9. USB mini-B (U-B)
This port is used for transferring screen programs or connecting a PictBridge-compatible printer.
10. Fall prevention tabs
These tabs prevent the V9 series unit from falling off the mounting panel until the mounting fixtures
are tightened.
11. DIP switches
This 8-bit DIP switch is used for setting the terminating resistance of the MJ1/MJ2 RS-485 signal
line.
12. Sliding switch
This switch is for selecting the RS-232C/RS-485 signal (2-wire connection) or the RS-422 signal
(4-wire connection) for MJ2. The upper side is for the RS-232C/RS-485 signal (2-wire connection)
and the lower side is for the RS-422 signal (4-wire connection).
13. Power supply terminal block
This terminal block is for supplying power (24 VDC) to the V9 series unit.
14. USB-A (U-A)
This port is used to connect a printer, USB flash drive, keyboard, or mouse.
15. Modular jack 1 (MJ1)
This connector is used for screen program transfer and connection with PLCs or other peripheral
devices.
16. Modular jack 2 (MJ2)
This connector is used for connection with PLCs or other peripheral devices.
17. 100BASE-TX/10BASE-T connector (LAN)
This connector is used for Ethernet communication.
18. Mounting holes
The mounting holes are used for inserting fixtures when securing the V9 series unit to a mounting
panel.
19. DIP switches (optional “DUR-00” unit)
These switches are used for setting the terminating resistance of the CN1 signal line.
20. PLC communication connector (CN1) (optional “DUR-00” unit)
This connector is used for connection to a controller (PLC, temperature controller, inverter, etc.).
21. FG terminal (FG) (optional “DUR-00” unit)
This is used for connecting FG wire of the communication cable.
3-12 2. Specifications of Components
2. Specifications of Components
Serial Connector (CN1)
This connector is used to connect a controller or barcode reader via RS-232C, or connect a controller
via RS-422/485.
For the V907xiW/V9060iTD, attach the optional “DUR-00” unit to add this serial connector.
The serial connector pins correspond to the signals as shown below.
*1 The signal level can be changed between RS-232C and RS-422/485 in the configuration software.
When RS-232C is selected, set DIP switches 5 and 7 to the OFF position.
(For details on DIP switches, refer to “DIP Switches (DIPSW)” (page 3-30).)
*2 When RS-422/485 is selected, +5 V is output from pin No. 9.
This +5 V is used as the power supply for the external terminating resistance when performing RS-422/485
communication. It cannot be used as an external power supply.
Bottom view Bottom view
V9100 V9080
Rear view
V907xiW
CN1 (D-sub 9-pin, female)
Pin No.
RS-232C
*1
RS-422 / RS-485
*1
Signal Description Signal Description
1 NC Not used + RD Receive data (+)
2 RD Receive data RD Receive data ()
3 SD Send data SD Send data ()
4 NC Not used + SD Send data (+)
5 SG Signal ground SG Signal ground
6 NC Not used + RTS Request to send (+)
7 RTS Request to send RTS Request to send ()
8 CTS Clear to send NC Not used
9 NC Not used + 5 V
Use prohibited
*2
9
5
6
1
3
2. Specifications of Components 3-13
Names and Specifications of Components
Recommended Connector
The following connector is recommended for custom-made cables.
Applications
Modular Jack (MJ1/MJ2)
The modular jacks are used for connection to a screen program transfer cable (MJ1 only), temperature
controller, barcode reader, and other devices.
The pins of MJ1 and MJ2 correspond to the signals as shown below.
V9150, V9120, V9100, V910xiW, V9080 series
*1 When the mounting angle is 15 to 60, or 120 to 135, the +5 V external power supply at MJ1/MJ2 of the V9
series unit is impossible.
*2 Allowable current for the +5 V external power supply at MJ1/MJ2 of the V9 series unit
For MJ1 and MJ2, the maximum allowable current is 150 mA in total (only when the mounting angle is 60 to
120).
Recommended
Connector
17JE-23090-02(D8C)-CG
manufactured by DDK
D-sub 9-pin / male / inch screw thread (#4-40UNC) type
/ with hood / lead and cadmium free
Application V-SFT-6 Setting Refer to
PLC/temperature controller connection Required
V9 Series Connection ManualBarcode reader connection Required
Multi-link/Multi-link2 communication Required
Bottom view Bottom view
V9100 V907xiW
MJ1/2 Pin No. Signal Description
1 +SD/RD RS-485 + data
2 SD/RD RS-485 data
3+5 V
Externally supplied +5 V
*1
*2
4+5 V
5SG
Signal ground
6SG
7 RD RS-232C receive data
8 SD RS-232C send data
8 76 5 43 21