00198711-01_UM_X-Serie-S_EN.pdf - 第329页
Instruction manual SIPLACE X-Series S 6 Station extensions From software version 713.0 Edition 11/2019 6.7 Fixed component table for tray feeders 329 6.7 Fixed component t able for tray feeders Item no. 00519990- xx Fixe…
6 Station extensions Instruction manual SIPLACE X-Series S
6.6 SIPLACE JTF-S/JTF-M From software version 713.0 Edition 11/2019
328
6.6.3 Technical data
6
SIPLACE JTF-S SIPLACE JTF-M
Width
162 mm 177 mm
Height
587 mm 587 mm
JEDEC waffle pack tray specification JEDEC Standard: 95-1 & IEC 60286-5
Storage capacity
Waffle pack tray, thin 30 JEDEC waffle pack trays 18 JEDEC waffle pack trays
Waffle pack tray, thick 20 JEDEC waffle pack trays 14 JEDEC waffle pack trays
Waffle pack tray changeover time
< 5 seconds (depending on
application)
--
Slot n to n+1 -- 3.5 seconds
Slot 1 to 18 -- 10 seconds
Slot 18 to 1 -- 8.9 seconds
Cassette
--
Dimensions -- approx. 330 mm x 150 mm x 230
mm
Max. load capacity -- 2.7 kg (150 g each for 18 slots)
Pneumatics
4.1 bar to 5.5 bar 5.2 bar to 9 bar
Compressed air consumption
< 28.3 NL/min. < 28.3 NL/min.
Instruction manual SIPLACE X-Series S 6 Station extensions
From software version 713.0 Edition 11/2019 6.7 Fixed component table for tray feeders
329
6.7 Fixed component table for tray feeders
Item no. 00519990-xx Fixed component table for tray feeders
This component table is a fixed installation at the location and is required for use of the following
feeders:
– SIPLACE JTF-S
– SIPLACE JTF-M
It has room for a JTF-S or a JTF-M. The fixed component table can be fitted at location 2 and /or
location 3.
6
6
WARNING
Free locations with dummy feeder modules
Free locations need to be occupied with dummy feeders.
PLEASE NOTE
For more information, refer to the "User Guide JTF-S/JTF-M", German+English [Item No.
00197446-xx]
6 Station extensions Instruction manual SIPLACE X-Series S
6.8 3D coplanarity laser module From software version 713.0 Edition 11/2019
330
6.8 3D coplanarity laser module
Item no. 519807-xx 3-D coplan, X2 S / X3 S / X4 S
The 3D coplanarity laser module works with a line of laser light. This enables you to generate and
analyze the height profile of a two-dimensional arrangement of component leads e.g. BGA, QFP
etc. This analysis provides data about the coplanarity (contact plane) and collinearity (contact line
straightness) of component leads or balls.
For more details, refer to the "Assembly Instructions 3D Sensor", German+English [Item. no.
00197084-xx]
6.8.1 Safety instructions for coplanarity module sensor
The sensor works with a semiconductor laser which has a wave length of 670 nm (visible/red).
The maximum optical output is 60 mW.
The sensor is classified as laser class 3B.
– When using the sensor, always observe the IEC 60825-1:2014 regulations about "Safety of
Laser Equipment" and the accident prevention guidelines for "Laser Radiation" (DGUV Reg-
ulation 11), applicable in Germany.
– Also observe the accident prevention regulations of your own country!
The following warning labels are attached to the front and back of the sensor housing:
6
Fig. 6.8 - 1 Laser class 3B classification for the sensor