00191369-01.pdf - 第49页
User Manual HS-50 2 Operational Safety Software-Version 5.01Edition 01/99 2.1 Safety instructions 47 2SHUDWLRQDO6DIHW\ 6DIHW\ LQVWUXFWLRQV &RQY HQWLRQVIRUWKHXVHRIKD]DUGV\ PEROV This User Manual co…
1 Introduction User Manual HS-50
1.15 Overview of the modules - PCB conveyor Software Version 5.01 01/99 Issue
46
The conveyor belts are driven by DC motors. Each placement area has a lifting table for
clamping the PCBs. The width of the PCB conveyor can be adjusted either
– via the menu or
– using the line computer
7HFKQLFDOGDWDVLQJOHFRQYH\RU
7HFKQLFDOGDWDGXDOFRQYH\RU
PCB format 50 mm x 50 mm to 368 mm x 460 mm
2" x 2" to 14.5 " x 18 "
PCB thickness 0.3 mm to 4.5 mm
Maximum PCB curvature On top: 4.5 mm - PCB thickness
On bottom: 0.3 mm + PCB thickness
Clearance underneath PCB Standard: 25 mm
Option: Up to 40 mm
PCB conveyor height 830 ± 15 mm (standard)
950 ± 15 mm (option) SMEMA
Type of interface Siemens (standard)
SMEMA (option)
Clear guide edge of component 3 mm
PCB changeover time 2.5 s
PCB format 50 mm x 50 mm to 368 mm x 216 mm
2" x 2" to 14.5 " x 8.5 "
Fixed edge of conveyor Right (standard), left (option)
Placement sequence per conveyor Synchronous: same or different
Asynchronous: same
PCB width per conveyor Synchronous: different
Asynchronous: same
Ink spot recognition Synchronous: not possible
Asynchronous: possible
Automatic width adjustment Synchronous: not possible
Asynchronous: possible
User Manual HS-50 2 Operational Safety
Software-Version 5.01Edition 01/99 2.1 Safety instructions
47
2SHUDWLRQDO6DIHW\
6DIHW\LQVWUXFWLRQV
&RQY HQWLRQVIRUWKHXVHRIKD]DUGV\ PEROV
This User Manual contains notes that must be observed to guarantee your personal safety and to
avoid damage to equipment. These notes are highlighted by warning triangles and are indicated
as follows according to the level of risk:
DANGER or
as used in this User Manual means that death, severe injury or considerable damage to equip-
ment may occur if the danger instructions are not followed.
WARNING or
as used in this User Manual means that death, severe injury or considerable damage to equip-
ment may occur if the warning instructions are not followed.
CAUTION or
as used in this User Manual means that slight injury or damage to equipment may occur if the cau-
tion instructions are not followed.
PLEASE NOTE
as used in this User Manual provides information on the product or indicates a part of the User
Manual that requires particular attention.
4XDOLILHGSHUVRQQHO
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and maintenance of automatic placement systems and add-on devices and are suitably
qualified, e.g.
– have been trained, instructed or authorized to switch on and off, isolate, earth and identify elec-
trical circuits and system components in accordance with normal safety standards.
2 Operational Safety User Manual HS-50
2.1 Safety instructions Software-Version 5.01 Edition 01/99
48
– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-
cordance with normal safety standards.
– have received first aid training.
8VHDVSUHVFULEHG
WARNING
The product must only be used for the applications specified in the catalogs and technical
descriptions, and then only in conjunction with non-Siemens devices and components that have
been recommended or approved by Siemens. For the product to operate correctly and reliably, it
must have been transported, stored, erected and assembled correctly and must be operated and
maintained with care.
,PSRUWDQWQRWHVRQRSHUDWLRQDOVDIHW\
WARNING
The following points MUST be observed in order to maintain operational safety:
Å NEVER open one of the protective covers if you are not totally familiar with the use and
functioning of the machine! Do not open the protective covers during operation unless you are
told to do so in this Manual or in the station software dialog.
Å The key switch must only be set to set-up mode ("I") by trained and qualified personnel.
Do not set turn the key switch to the position "I" (set-up mode) during operation unless promp-
ted to do so in this Manual or in the station software dialog
Å NEVER place your head or arms in the gantry travelling range while the station is switched on!
Å Never make changes, however minor, unless you are totally aware of the effect they will have
on the overall functioning of the system.
Å The stations must always be set up, retooled and maintained by appropriately trained person-
nel.
Å Only use Siemens original spare parts and authorized accessories. The use of other parts will
affect safety and may invalidate the liability for any consequential damage.
Å The operational safety of SMD automatic placement systems can be guaranteed only if the sy-
stem is used as prescribed and in accordance with the instructions in the User/Service Manu-
als.