00198377-01_SM_JTF-ML2_en.pdf - 第9页
1 Introduction 1.1 Safety Instructions Service Manual SIPLACE JTF-ML2 08/2017 9 1.1.3.3 Safety of Plant and Equipment ► Never make changes, however minor, unless you are totally aware of the effect they will have on the …
1 Introduction
1.1 Safety Instructions
8 Service Manual SIPLACE JTF-ML2 08/2017
1.1.3 Important notes on operational safety
The following points must be observed in order to maintain operational safety:
1.1.3.1 General
► Operational safety is only guaranteed during use of the user manual as prescribed.
► Always observe the applicable accident prevention regulations and the special safety regula-
tions in your country!
► Make sure that the warning labels are always clearly identifiable and always easily readable.
► Replace any damaged warning or notice labels. Replace any labels that are missing.
► The machine key for releasing the covers on the machine must be kept in a safe place where
it is only accessible to qualified personnel.
► If you need to work on the machine and you do not have adequately trained personnel at your
company, always call in a service engineer from ASM Assembly Systems GmbH & Co. KG!
ASM Assembly Systems GmbH & Co. KG will not accept liability for any damage or con-
sequential damage that is the result of incorrect work!
► If particularly hazardous situations are identified while the module is in use, the module owner
must immediately notify the manufacturer in writing so that appropriate action can be taken to
reduce the potential danger.
► Wear safety glasses when using alcohol to clean the conveyor belt.
WARNING
Safe operation of module
In spite of all the safety precautions taken by the manufacturer, failure to use the module as
prescribed can result in severe physical injury and/or considerable damage to equipment!
For the module to be safe, it must be used correctly by qualified personnel and all warnings
must be observed. Some work requires training that goes beyond the scope of this Manual.
1.1.3.2 Safety of Operators and Other Persons
► Module operators may only carry out work for which they have been adequately trained and
with which they are totally familiar!
► NEVER open one of the covers if you are not totally familiar with the use and functioning of
the module! Do not open the covers during operation unless you are told to do so in this
Manual or in the station software dialog!
► For your own safety, wear work clothes that conform to the guidelines of the professional
association, i.e. no wide sleeves etc.
► Reduce the risks by not wearing scarves, chains or ties at your work post.
► People with long hair must wear a protective head covering.
WARNING
Voltage
The module is electrically driven. When electrical devices are in use, certain parts carry
dangerous voltage levels!
► Before performing any work to parts which conduct electricity, switch the machine off
at the main switch and unplug the Lemosa socket for the adapter, to disconnect the
power between the module and the machine.
ð There is a risk of death, severe injury and/or considerable damage to equipment if
these instructions are not followed.
1 Introduction
1.1 Safety Instructions
Service Manual SIPLACE JTF-ML2 08/2017 9
1.1.3.3 Safety of Plant and Equipment
► Never make changes, however minor, unless you are totally aware of the effect they will have
on the overall functioning of the module and system!
► The modules must always be set up, retooled and maintained by appropriately trained person-
nel.
► Do not make modifications to the safety equipment. In particular, NEVER deactivate circuit-
breakers or remove safety devices.
1.1.4 Danger of Crushing at the SIPLACE JTF-ML2
Fig.1: EMERGENCY STOP button
The SIPLACE JTF-ML2 (JEDEC tray feeder) stops
when the EMERGENCY STOP button (1) is pressed.
DANGER
Danger of crushing
There is a risk of injuries by pinch points or a risk of crushing by reaching into the feeder or
from loose clothing which could get into the feeder during operation.
► Observe correct handling and the safety instructions.
► Do not reach into the feeder while it is running.
► Maintain an adequate safety distance.
Areas of the SIPLACE JTF-ML2 at which there is a danger of crushing
Fig.2: Do not reach into the JTF_ML2 or into the machine
through the JTF_ML2.
Fig.3: Moving magazine
1 Introduction
1.1 Safety Instructions
10 Service Manual SIPLACE JTF-ML2 08/2017
Fig.4: Conveyor belt rollers Fig.5: Pusher
Fig.6: Side tray clamp
1.1.5 Safety Instructions for Transporting the Module
Fig.7: Holding the tower
CAUTION!
Tower weight
The weight of the tower (26.3 kg) could cause in-
juries if the module is not handled correctly.
Always hold the tower with two hands. Use the
handles on the sides of the tower.
Tower and conveyor must be transported separ-
ately. Mishandling will cause damage to the
SIPLACE JTF‑ML2.
.