iTAC Advance Issue 2, Mar 2018.pdf - 第69页

69 Issue 2 , Mar 18 Note: For Work Order handling, route A , B works with assign and merge, route D works with Process Interlocking. Is Printer 1 st machine on the line connected to the iTAC? (Assign/ Merge or Interlocki…

Issue 2, Mar 18

Sales support - technical details to be known before PO

We need to make sure that iTAC option will work for customer who wants to buy the iTAC option,

therefore is recommended to clarify all technical details:

The software is RTX, ensure that customer not using RTX software already. It is based on SP15 –

should be checked that it will work for customer.

Is machine capable to run SP15 software? If DEK software on machine is older than 09 SP15, few

checks must be completed prior software upgrade such as:

• The software is not compatible with the Dunkermotoren BGE9010

• Nextmove ES card part number must be 193409

• For machines using Hawkeye (Deposit Verification) please check that encoder connector is

fitted into the M36 in slot x6

All details can be found in TB466.

It should be agreed with customer which operating system will be used.

If customer requires upgrade from WinXP to WES7 first must be checked whether machine is fitted

with compatible PC:

• If the PC is fitted with Q35 or H81 only Microsoft licence required

Software upgrade to WES7 for Q35 pc - MPU 602360*1

Software upgrade to WES7 for H81 pc – MPU 602377*1

• If Printer is fitted with other PC it must be replaced – MPU 602376*1 to be ordered

All details regarding 09SP15 compatibility and WES7 upgrade including associated checks and

upgrades can be found in TB431.

Customer to define which options wants to use – Refer to Workbook to see all available/supported

options.

Option

Description

Available

Comments

Option 1

Workorder Handling

A, B, D

Option 2.1

Check Get Process Data

Option 2.2

Load Program

TBA

Pending planning

Option 3.1

Create Setup Internal

Option 3.2

Create Setup External

Not Applicable

Option 3.3

Check Setup

Option 3.4

Equipment Setup

Option 4

Process Interlocking

Option 5

Assign Serial Number

Option 5.1

Merge Serial Number

Option 6.1

Upload Only process data

No request for this

Option 6.2

Upload process data and status

Option 6.3

Upload failure data and status

TBA

Pending planning

Option 7

Status Condition

TBA

Pending planning

Issue 2, Mar 18

Note: For Work Order handling, route A, B works with assign and merge, route D works with

Process Interlocking.

Is Printer 1

machine on the line connected to the iTAC? (Assign/Merge or Interlocking)

iTAC option is applicable only for machines with standard and HTC conveyor. It is not compatible

with machine fitted with RTC conveyor. HTC conveyor should be used ideally in 1 stage mode for

inroad conveyor – difficulties to remove PCB from inroad conveyor. 3 stage mode could be used only

if the remote barcode reader is 100% reliable.

iTAC is not compatible with APC (APC is merged into SP16, but iTAC RTX is based on SP15)

Which remote and handheld scanner will be used?

This has to be pre-agreed with customer prior purchase order. Customer has to be aware of 1 serial

port availability on machine PC as well – if wish to use separate remote scanners for the Top &

Bottom side, the scanners have to be connected in daisy chain mode or similar requiring only one

RS232 port.

Customer has to be aware of fixed setting of COM Port (slow baud rate).

Type of the panel barcodes (label or laser edged), size and density should be clarified as well.

It should be decided about barcode format for material & equipment - - Barcode Parameters based

on machine file or product file?

Equipment based on P/N or equipment description?

Will be used standard MES key and product identification in recipe?

NOTES:

Issue 2, Mar 18

iTAC option testing on the printer

Objective HO 19: Carry out all the steps in DEK Test Scenario and record the result

Variant 1:

Variant 1

Step

Step Action Description

Expected Result

Actual Result

Top side.Assign & upload state

(PASS/PASS) PCB for the laser

marking machine. Activate WO on

the line. Load correct program for

PN activated in iTAC

Unverified (red cross) equipment

and material

Check iTAC server on TR \ MIS -

Work order \ Order

No material should be setup on the

line and no equipment rigged on the

Open cover and scan required

equipment & material

All equipment and material should

be verified (green tick)

Check iTAC server on TR \ MIS -

Work order \ Order

scanned material should be setup

on the line and scanned equipment

rigged on the WO

Activate setup of current WO

WO should be activated

Scan (PASS/PASS) PCB on

upline conveyor

PCB should be accepted by

machine

Place PCB with no barcode on

upline conveyor

PCB should be rejected by machine

due to missing barcode

Scan PCB with barcode which is

not assigned to the laser marking

machine

PCB should be accepted by

machine

Assign & upload state

(PASS/FAIL) PCB for the laser

marking machine. Scan

(PASS/FAIL) PCB on upline

conveyor

PCB should be rejected by machine

Assign & upload state

(PASS/SCRAP) for multiple PCB

for the laser marking

machine.Scan (PASS/SCRAP)

PCB on upline conveyor

PCB should be accepted by

machine

Assign & upload state (SCRAP)

for multiple PCB for the laser

marking machine.Scan (SCRAP)

PCB on upline conveyor

PCB should be rejected by machine

Bottom side.Change iTAC plugin

for bottom side, load

corresponding program. Verify

Items.

All equipment and material should

be verified (green tick)