SIPLACE Line Computer UNIX.pdf - 第33页
User Manual Line Computer UNIX 1 Introduction and Installation Software Vers ion 502.xx 10/2000 Issue 1.5 Software Ins tallation 31 I t I I After a while, the following messag es are dis played on the scr een: This is t …
1 Introduction and Installation User Manual Line Computer UNIX
1.5 Software Installation Software Version 502.xx 10/2000 Issue
30
I
t I I
1.5.2 Definition of Terms
- Initial Installation
Prior to the start of the installation of the LC software, the computer must be in a neutral state, i.e. the
SCO OpenServer 5.0.4 or 5.05 operating system has been installed, but no further data exist on the
hard disk yet. This basic state exists when the unit is delivered.
When the LC software is then installed with the aid of the installation program, also the sample master
data are installed on the hard disk.
- Update
When the only difference between the new LC software and the one already installed is their revision
level, (e.g.
LRU.501.01 => LRU.501.03) this is referred to as an update. Any errors that may have
occurred in the predecessor version have been eliminated in the update version, and the software has
been optimized. In the case of an update, the master data are retained.
- Upgrade
When the new software differs from the one already installed in that their version designations are
different, (e.g. LRU.501.03 => LRU.502.01) this is referred to as an upgrade.
An upgrade version con-
tains new functions. In the case of an upgrade, the master data are retained and, if required, automati-
cally converted into the new data format.
1.5.3 Installation of LC Software
● Insert the Boot Diskette (1).
ATTENTION !
Be sure to use only the boot diskette appropriate for your specific computer type (see section 1.5.1).
● Turn on the UPS.
● Press RETURN when the line "Boot:" is displayed on the screen.
The line computer is now booted from the diskette.
After approx. 1 minute the following message is displayed on the screen:
Insert installdisk and press <Return> to continue
or remove the bootdisk and press <Return> to quit (ignore Warnings)
NOTE
When this message is displayed, the installation procedure can still be stopped by removing the boot
diskette and subsequently pressing the RETURN key. The error messages subsequently displayed
can be ignored. The state of the LC software is unchanged.
● Remove Boot Diskette, insert Installation Diskette (2) and press RETURN.
User Manual Line Computer UNIX 1 Introduction and Installation
Software Version 502.xx 10/2000 Issue 1.5 Software Installation
31
I
t I I
After a while, the following messages are displayed on the screen:
This is the last point to abort the LRU-installation
without changing any data.
If you have installed OEM-software, you have to reinstall it
after the LRU-installation
Do you want to continue the LRU-installation [y/n]
Abort Installation:
● Enter n for the installation to be aborted and then press RETURN.
The following steps are displayed for terminating the installation procedure and rebooting the
line computer:
Next steps
1.) Remove the floppy after the Safe to Power Off message
2.) reboot your system
3.) login as plr
** Safe to Power Off **
- or -
** Press Any Key to Reboot **
The computer can now be rebooted. The LC software’s state is still unchanged.
Continue Installation:
● Enter y to continue the installation process and then press RETURN.
The computer system is shut down. The following steps are displayed for continuing the
installation procedure:
PL EA pre-install finished
Next steps
1.) Remove the floppy after the Safe to Power Off message
2.) insert the CD
3.) reboot your system
4.) login as plr
** Safe to Power Off **
- or -
** Press Any Key to Reboot **
1 Introduction and Installation User Manual Line Computer UNIX
1.5 Software Installation Software Version 502.xx 10/2000 Issue
32
I
t I I
● Remove Installation Diskette and insert the CD-ROM.
● Press any key on the keyboard.
The system is rebooted. When the booting procedure has been completed, the following lines
are displayed:
login:
● Enter plr after "login:" and press RETURN.
Password:
● Enter plr after "Password" and press RETURN.
NOTE
With some hardware configurations the message Terminal is ansi is displayed.
● Acknowledge this message by pressing RETURN.
The CD-ROM is now read in. This takes approx. 10 minutes.
While the data are being read in, information about the ongoing activities is displayed.
If no data are available in the line computer, the following query appears:
There is no user data (SDH) on the line computer.
Do you want to install:
Do you want to install default libraries (GF-/BE-/RI-Bibliothek..) [1]
User data (SDH) saved from old installation [2]
Do not install any data [3]
Please select your choice... ’1’, ’2’ or ’3’
If option 1 is selected, the default libraries will be installed,
if option 3 is selected, only the ST-Bibliothek,
if option 2 is selected, the data previously saved under SCO 3.0 or SCO 5.0 are restored. In this
case the operator is prompted to insert the diskette and the tape containing the backed-up data.
CAUTION
If options 1 and 3 are selected, the line configuration needs to be performed via the Line Editor follo-
wing the installation (see chapt. 12, section 12.2).
● Enter the number of the desired option and confirm by pressing RETURN.
The selected data will be installed.