SIPLACE Line Computer UNIX.pdf - 第420页
13 Production Tools / Set-Up User Manual Line Compu ter UNIX 13.1 Set-Up E ditor (Feeder Part and WPC/MTC Editors) Software V ersion 502.xx 10/2000 Issue 418 I t I I - Delete When this icon is a ctive, th e editor is in …
User Manual Line Computer UNIX 13 Production Tools / Set-Up
Software Version 502.xx 10/2000 Issue 13.1 Set-Up Editor (Feeder Part and WPC/MTC Editors)
417
I
t I I
For selecting the levels in the WPC/MTC Editor the following clicking sequence must be observed:
● first click on the level in the "Levels" display area, then
● click on the level in the "WPC/MTC" display area.
- Machine options of the feeder list --> Tracks (in the Feeder Part Editor)
The machine options of the feeder list (except for the waffle pack trays) can be allocated to the tracks
of a feeder part. Only the six tracks identified in green at the upper and lower borders of the feeder
part cannot be occupied by these machine options.
- Waffle pack tray --> Waffle pack tray carrier and manual trays
Waffle pack trays are set up on waffle pack tray carriers. A waffle pack tray carrier can be assigned
any number of waffle pack trays.
- Waffle pack tray/waffle pack tray carrier --> Level (in the WPC/MTC Editor)
For selecting the levels in the WPC/MTC Editor the following clicking sequence must be observed:
● first click on the level in the "Levels" display area, then
● click on the level in the "WPC/MTC" display area.
- Feeder (linear feeder) --> Module
Linear feeders must be set up on a module. The module must be set up before the linear feeders are
assigned to it.
- Component --> Feeder (in the Feeder Part Editor)
The components are allocated to the feeder divisions individually. An empty division is marked in blue,
an occupied division in green.
- Component --> Waffle pack tray (in both editors)
Only one component type can be allocated to a waffle pack tray. All divisions therefore contain same
type of component. Empty divisions are highlighted in blue, occupied divisions in green.
- Nozzle --> Nozzle Changer location (division)
In addition to the configured nozzles, further nozzles can be defined in the Machine Options Editor.
- Options of the options list --> Tracks (in the Feeder Part Editor)
The options list is required for the station configuration. The options are permanently allocated to the
tracks. An exception is the WPC, the MTC and the component disposal conveyor. They may also be
allocated in the Feeder Part Editor for a specific setup only. It is therefore possible to manage, for
example, setups with and without WPC in parallel without any need for the station configuration to be
changed.
13 Production Tools / Set-Up User Manual Line Computer UNIX
13.1 Set-Up Editor (Feeder Part and WPC/MTC Editors) Software Version 502.xx 10/2000 Issue
418
I
t I I
- Delete
When this icon is active, the editor is in the deletion mode. All feeding units and components in the
display area can thus be deleted. Prior to the deletion being carried out, a dialog box is displayed
asking you to confirm the deletion.
NOTE
After the deletion operation is completed, another mode should be activated as otherwise feeding
units and components are likely to be inadvertently deleted.
● Click on .
● In the display area click on the feeding unit or component you want to delete.
A dialog box is displayed.
● Click on OK if you want the deletion to be carried out, or Cancel if you do not want the deletion to
be executed.
NOTE
If a waffle pack tray carrier is deleted, all waffle pack trays set up on it are also deleted.
For the selection of levels in the WPC/MTC Editor, the following clicking sequence must be observed:
● first click on the level in the "Levels" display area, then
● click on the level in the "WPC/MTC" display area.
- Move
When this icon is active, the editor is in the moving mode. All feeding units and components in the dis-
play area can thus be moved.
On a station, the feeding units can be moved within a feeder part, the components can be moved to
different feeders.
In the case of Waffle Pack Changers or Matrix Tray Changers, the feeding units and components can
be moved between levels.
NOTE
The clicking sequence for moving can be carried out in either direction: either, as described above,
click on the object first and then the target, or click on the target first and then the object.
If an object cannot be moved to the indicated target, a corresponding error message is displayed which
must be acknowledged.
User Manual Line Computer UNIX 13 Production Tools / Set-Up
Software Version 502.xx 10/2000 Issue 13.1 Set-Up Editor (Feeder Part and WPC/MTC Editors)
419
I
t I I
● Click on .
● In the display area, click on the feeding unit or component you want to move.
● Click on the new location.
The feeding unit or component is displayed at the new location.
NOTE
For selecting the levels in the WPC/MTC Editor, the following clicking sequence must be observed:
● first click on the level in the "Levels" display area, then
● click on the level in the "WPC/MTC" display area.
- Copy
If this icon is active, the editor is in the copy mode allowing all machine options and components in the
display area to be copied.
In the case of a station, the machine options may be copied within a feeder area and components to
empty feeder compartments.
In the case of a Waffle Pack Changer or Matrix Tray Changer, waffle pack trays may be copied to
waffle-pack tray carriers and waffle pack tray carriers to unoccupied levels.
NOTE
The clicking sequence during copying may be carried out in either direction: either, as described, click
on the object first and then on the target, or else first on the target and then on the object.
If an object cannot be copied to the specified target, a corresponding error message will appear which
needs to be acknowledged.
● Click on .
● In the display area click on the machine option or the component you wish to copy.
● Click on the desired location.
The copied object will be displayed at the selected location.