00198150-02_SM_TX_en.pdf - 第280页

12 SIPLACE TX-Series Component Trolley 12.2 Replacing the Rollers 280 Service Manual SIPLACE TX Series 06/2017 12.2 Replacing the Rollers Parts, equipment and tools ● Front roller LDA-VPA 75K-EL-47994 [03004958-xx] ● Bac…

12 SIPLACE TX-Series Component Trolley

12.1 SIPLACE TX-Series Component Trolley - Overview

Service Manual SIPLACE TX Series 06/2017 279

12 SIPLACE TX-Series Component Trolley

DANGER

Observe User Manual

► Please observe the safety instructions in the user manual for all work!

12.1 SIPLACE TX-Series Component Trolley - Overview

Fig.395: Component trolley overview

1. Actuator/protective bracket

12.6 "Replacing the Actuator/Protective

Bracket" [}284]

2. Feeder centering

12.7 "Replacing the Feeder Centering

[03028910-xx]" [}285]

3. Guide profile (Ω profile) and

feeder entering guide

12.4 "Replacing the Guide Profile/Entering Guide

Feeder" [}282]

12.4 "Replacing the Guide Profile/Entering Guide

Feeder" [}282]

4. Tape waste container

5. Reels

12.2 "Replacing the Rollers" [}280]

6. Bearing assembly

12.5 "Replacing the Bearing Assembly (Centering

Sleeve) [03103947-xx]" [}283]

7. Locking latch

12.3 "Replacing the Locking Latch [03069205-

xx]" [}280]

8. Changeover table

9. Stop bar with centering holes

12 SIPLACE TX-Series Component Trolley

12.2 Replacing the Rollers

280 Service Manual SIPLACE TX Series 06/2017

12.2 Replacing the Rollers

Parts, equipment and tools

●

Front roller LDA-VPA 75K-EL-47994 [03004958-xx]

●

Back roller LPA-POA 50G [03121354-xx]

●

Second Person

Overview

Fig.396: Rolls on COT

1. Back roller LPA-POA 50G [03121354-xx]

2. Front roller LDA-VPA 75K-EL-47994 [03004958-

xx]

 CAUTION!

Heavy machine part!

The component trolley must be placed on one

side in order to remove the rollers. You will need

two people to perform this task.

Removal

► Move the component trolleys out of the machine.

► Remove all feeders.

► Place the component trolley on its side on a suitable surface.

► Remove the fastening screws on the roller to be replaced

► Remove the roller.

Installation

► Fit the new roller.

► Stand the component trolley on its wheels again.

12.3 Replacing the Locking Latch [03069205-xx]

Parts, equipment and tools

●

Single locking latch [03069205-xx]

●

Tension spring [03010352-xx]

●

Cover plate for locking strip [03077142-xx]

NOTICE

SIPLACE TX/X/SX Series Component Trolley

Component trolleys from the SIPLACE TX, SX and X-Series (S) require a locking latch for

each feeder track.

► Feeder lock [03023777-xx] with 40 locking latches

(1x per component trolley SIPLACE TX/X-Series (S)/SX4)

ð The feeder lock can also be completely dismantled from the component trolley and

replaced.

12 SIPLACE TX-Series Component Trolley

12.3 Replacing the Locking Latch [03069205-xx]

Service Manual SIPLACE TX Series 06/2017 281

Overview

Fig.397: Locking latch on component trolley

1. Tape waste container

2. Operation cover

3. Position of complete feeder locking mechanism

4. Locking latch

5. Tension spring

6. Pressure plate (under cover(2))

Removal / Installation

► Remove the waste tape container (1) and empty it.

► Refit the waste tape container. This makes sure that any parts which fall down are not lost.

NOTICE

Waster tape container

You can use the waste tape container as a surface on which to place small parts e.g. ten-

sion springs, locking latches etc.

► Remove the screws fastening the cover plate locking rail [03077142-xx](2). Use a suitable

Phillips screwdriver to avoid damaging the screws.

Fig.398: Removing locking latch

► Unhook all tension springs (1) from the locking

latches (2).

► Remove the screws (3) fastening the pressure

plates(4).

► Pull out the locking latches with the shaft(5).

► The locking latches can now be pushed off the

shaft.

► Return the locking latches, including the new

one, to the shaft.

► Fit the locking latches and shaft.

► During reassembly, take care to keep the pressure plates in their correct position (4). These

are not symmetrical and will not hold the shaft properly if placed in a certain (incorrect) posi-

tion.

► When tightening the fastening screws (3), make sure that the pressure plates (4) are not at an

incorrect angle and that the locking latches do not jam.

► Hook the tension springs (1) back up.

► Refit the cover.