00197394-03_AI_Smart-Pin-Support_X-S_DE_EN.pdf - 第80页

1 Introduction 1.5 Abbreviations 80 Assembly Instructions / Montageanleitung SIPLACE X-Series S Smart Pin Support 05/2019 1.5 Abbreviations Abbreviations Description PA, PA1, PA2 Placement area, Placement area 1, Placeme…

1 Introduction

1.4 Staff qualifications and training

Assembly Instructions / Montageanleitung SIPLACE X-Series S Smart Pin Support 05/2019 79

1.3.3.5 Dispatching ESD modules

► Always store modules and components in conductive packaging (e.g. metallized plastic bags

or metal sleeves) and dispatch them in conductive packaging

► If the packaging is not conductive, place the modules in a conductive envelope before pack-

aging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for

example. NEVER use plastic bags or film.

► If the module has integral batteries, ensure that the conductive packaging does not touch or

short circuit the battery terminals and, if necessary, first cover the terminals with insulating

tape or material.

1.3.4 Validity of Document

This document contains instructions about the service work for all SIPLACE X series S machines.

The work described in this manual is largely identical for all machine types:

●

Any differences will be explicitly indicated.

●

Diagrams should be seen as examples e.g. the diagram of a SIPLACEX3 S or a different

machine paint finish does not mean that the following information only applies to the machine

type shown.

Please refer to the circuit diagram folder for any electrical checks:

●

Circuit diagram SIPLACEX3S, X4S, X4iS [00197021-xx] (German/English)

1.3.5 Release History

Document

Smart Pin Support Option

SIPLACE X-Series S

Assembly instructions

Release Amendments

04/2013 Initial release

02/2014 Adjustments and supplements: new strain reliefs

05/2019 Adjustments and supplements:

●

Fitting the Q10 holder: note about technical information

●

Note about magazines without "magazine recognition board"

●

Restrictions: revision and supplements

●

Inserting the dummy feeder (new chapter)

●

Update of the chapter "Calibrating the pin picker, lifting tables and pin

magazines"

1.4 Staff qualifications and training

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and maintenance of the machine and the add-on devices and are suitably qualified, e.g.:

●

Have been trained, instructed or authorized to switch on and off, isolate, earth and identify

electrical circuits and system components in accordance with normal safety standards.

●

Have been trained or instructed in the upkeep and use of appropriate safety equipment in

accordance with normal safety standards.

●

Have received first aid training.

1 Introduction

1.5 Abbreviations

80 Assembly Instructions / Montageanleitung SIPLACE X-Series S Smart Pin Support 05/2019

1.5 Abbreviations

Abbreviations Description

PA, PA1, PA2 Placement area, Placement area 1, Placement area 2

CO Component

C&P Collect&Place

CPP Collect&Pick&Place head

ESD Electrostatic sensitive device

EMC Electromagnetic compatibility

PCB PCB board

P&P Pick&Place

NC Nozzle changers

TH TwinHead

2 Brief Description

2.1 Product Description

Assembly Instructions / Montageanleitung SIPLACE X-Series S Smart Pin Support 05/2019 81

2 Brief Description

Smart Pin Support facilitates automatic positioning of pins on the lifting table plate with the help of

the programming system. The pins can therefore be automatically positioned by the machine while

a new job is being downloaded to the machine.

2.1 Product Description

The "Smart Pin Support" option is available for the X3 S, X4 S and X4i S machines.

The pins are positioned on the lifting table plate with the help of SIPLACE Pro. The position of

these pins is described in SIPLACE Pro in the same way as in a placement list. The information is

then sent to the machine, together with the setup. The machine recognizes the available pins and

sets these at the programmed positions.

The pins are positioned with the help of the pin pickers. These are located on the gantries.

There are two magazine types available for this, W5 and Q10, which are recognized by the soft-

ware.

2.2 Prerequisites

The following conditions must be fulfilled for installation of the Smart Pin Support:

●

Station SW >706.1 SP1

●

SIPLACE Pro >10.1 SP1

2.3 Restrictions

●

You always need to install a pin picker at each of the machine gantries. These are fixed to the

left or right side of the gantry, depending on the configuration.

The X3 S machine, for example, only has a pin picker fitted on the right of gantry 3. This

means that the pins can only reach a range of 280 mm, not the entire placement area.

●

The W5 and Q10 magazine can be fitted.

NOTICE

From SW 706.1 SP2

From SW 706.1 SP2, magazines can be fitted without the "magazine recognition" function.

In this case, the machine can only be configured manually via the software (Autoconfig).

●

For all valid configurations, refer to section 2.4 "Possible Configurations/Required Equip-

ment" [}82].

●

Due to the pin picker, tracks 38 to 40 can not be reached by the placement head at locations

1 and 3. For this reason, the dummy feeder is used (see 3.7 "Inserting the dummy

feeder" [}115]).

●

The placement area is restricted in the X direction. The extent of this restriction depends on

the specific configuration.

Example:

SIPLACE X4S (PA1 with C&P20P / C&P20P, PA2 with Twin / CPP)

Restriction at gantry 1 (PA1): approx. 20mm

Restriction at gantry 3 (PA2):approx. 40mm