c900795.R02_EN.pdf - 第89页

4 Electrical Section 4-15 Serial DI Map ■ Device 2 Address Bit No. Signal Name Address Bit No. Signal Name 0000h 0 Device No. Bit 0 0004h 0 SERVO (F)/READY (F) 1 Device No. Bit 1 1 CANCEL (F)/RESET (F) 2 Device No. Bit 2…

100%1 / 120
4 Electrical Section
4-14
Address
Bit
No.
Signal Name Address
Bit
No.
Signal Name
0018h
0
Trigger Register Bit 0
001Ah
0
Trigger Register Bit 16
1
Trigger Register Bit 1
1
Trigger Register Bit 17
2
Trigger Register Bit 2
2
Trigger Register Bit 18
3
Trigger Register Bit 3
3
Trigger Register Bit 19
4
Trigger Register Bit 4
4
Trigger Register Bit 20
5
Trigger Register Bit 5
5
Trigger Register Bit 21
6
Trigger Register Bit 6
6
Trigger Register Bit 22
7
Trigger Register Bit 7
7
Trigger Register Bit 23
0019h 0
Trigger Register Bit 8
001Bh 0
Trigger Register Bit 24
1
Trigger Register Bit 9
1
Trigger Register Bit 25
2
Trigger Register Bit 10
2
Trigger Register Bit 26
3
Trigger Register Bit 11
3
Trigger Register Bit 27
4
Trigger Register Bit 12
4
Trigger Register Bit 28
5
Trigger Register Bit 13
5
Trigger Register Bit 29
6
Trigger Register Bit 14
6
Trigger Register Bit 30
7
Trigger Register Bit 15
7
Trigger Register Bit 31
■ Device 9
Address
Bit
No.
Signal Name Address
Bit
No.
Signal Name
0000h 0
CTF (Left Rear) Cover Lock
0002h 0
1
CTF (Left Rear) Shutter Open
1
2
CTF (Left Rear) Setup Switch
2
3
CTF (Left Rear) Safety Relay Rest
3
4
CTF (Left Rear) Servo ON Permission
4
5
5
6
6
7
7
4 Electrical Section
4-15
Serial DI Map
■ Device 2
Address
Bit
No.
Signal Name Address
Bit
No.
Signal Name
0000h 0 Device No. Bit 0 0004h 0 SERVO (F)/READY (F)
1 Device No. Bit 1 1 CANCEL (F)/RESET (F)
2 Device No. Bit 2 2 START (F)
3 Device No. Bit 3 3 CYCLE STOP (F)/ STOP (F)
4 Device Added Information Bit 0 4 RECOVERY (F)/CLEAR (F)
5 Device Added Information Bit 1 5
6 Device Added Information Bit 2 6
7 Output Register Value Bit 0 7 DOCKING (F) / (Right Front)
0001h 0 Output Register Value Bit 1 0005h 0
1 Output Register Value Bit 2 1 Tape Cutter Close (Right Front)
2 Output Register Value Bit 3 2 Tape Cutter Close (Left Front)
3 Output Register Value Bit 4 3 Tape Cutter Close ((Right Rear)
4 Input Register Value Bit 0 4 Tape Cutter Close (Left Rear)
5 Input Register Value Bit 1 5 Y1 Regenerative Resistor Thermal Alarm
6 Input Register Value Bit 2 6 Y2 Regenerative Resistor Thermal Alarm
7 Input Register Value Bit 3 7 X Regenerative Resistor Thermal Alarm
0002h 0 Y-axis OR- 0006h 0 SERVO (R)/ RESET (R)
1 Y-axis OR+ 1 CANCEL (R) / RESET (R)
2 2 START (R)
3 3 CYCLE STOPE (R) / STOP (R)
4 4 RECOVERY (R) / CLEAR (R)
5 5
6 UPS Under backup 6
7 UPS Battery Low 7 DOCKING (Left Rear)
0003h 0 Board Available Input 0007h 0
1 Ready Input 1
CTF(Right Rear) Power Relay ON
2 Regenerative Resistor 1 Thermo Alarm 2
3 Regenerative Resistor 2 Thermo Alarm 3
CTF(Right Rear) Connector Check
4 Regenerative Resister 3 Thermo Alarm 4
5 5
6 6
7
Fixed Camera Illumi. Trigger Invalid
7
4 Electrical Section
4-16
Address
Bit
No.
Signal Name Address
Bit
No.
Signal Name
0008h 0 000Ch 0 Entrance Sensor
1 1 Entrance Buffer Arrival
2 2 Board Stopper On
3 3 Board Stopper Off
4 CFB(F) / (Left Front) Lock (R) 4 Exit Sensor / Exit Buffer Arrival
5 CFB(F) / (Left Front) Lock (L) 5 Exit Buffer Slowdown
6 CFB(F) / (Left Front) Check 6 Board Stopper On 2
7 7 Board Stopper Off 2
0009h 0 CFB(Left Rear) Lock (R) 000Dh 0 Main Clamp Up / Push-up Pin Up
1 CFB(Left Rear) Lock (L) 1 Push-up Pin Down
2 CFB (Left Rear) Check 2 Quick Clamp Down (Front)
3 3
4 4 Quick Clamp Down (Rear)
5 5
Support Pins under Conveyor Rail
6 6
7 7
RTS-1(R) sensor
000Ah 0 ENABLE (F) / ACTIVE (F) 000Eh 0
1 ENABLE (R) / ACTIVE (R) 1
2
CTF(Right Rear) Positioning
2 ANC A Open
3 CTF (Left Rear) Insert Complete (L) 3 ANC A Close
4 CTF (Left Rear) Insert Complete (R) 4 Entrance Buffer Slowdown
5
Dot Station Paper Shortage
5 Main Conveyor Slow down 2
6 6
7 7 Main Conveyor Arrival
000Bh 0 000Fh 0 Main Conveyor Slowdown
1 1 Main Conveyor Arrival 2
2 Conveyor 1 Alarm 2
3 Conveyor 2 Alarm 3
4 Conveyor 3 Alarm 4
5 5
6 6
7 7