4OM-1431-006_w.pdf - 第137页

2-6 0709-001 2.2 List of W arning Messages W arning Codes Display Field A (Scope of W arning Messages) Display Field B (Details of W arning Messages) 010f31 P .C.B. existence The P .C.B was detected on the output conveyo…

100%1 / 271
2-50709-001
2.2 List of Warning Messages
Warning Codes Display Field A (Scope of Warning Messages)
Display Field B (Details of Warning Messages)
010f01 P.C.B. existence
Please remove the P.C.B. on the conveyor.
010f02 P.C.B. existence
Please remove the P.C.B. on the NL conveyor.
010f03 P.C.B. existence
Please remove the P.C.B. on the NA conveyor.
010f04 P.C.B. existence
Please remove the P.C.B. on the NB conveyor.
010f07 P.C.B. existence
There is no P.C.B. on the NL conveyor.
010f08 P.C.B. existence
There is no P.C.B. on the NA conveyor.
010f0b P.C.B. existence
There is no P.C.B. on the NR conveyor.
010f10 P.C.B. existence
Please remove the P.C.B of stage 1.
010f12 P.C.B. existence
The P.C.B is taken into the positioned place of stage 1.
010f14 P.C.B. existence
Please remove the P.C.B of the inlet of input buffer cnvr.
010f15 P.C.B. existence
Please remove the P.C.B of the positioning 1conveyor.
010f18 P.C.B. existence
Please remove the P.C.B of inlet and outlet of output cnvr.
010f19 P.C.B. existence
There is no P.C.B on the inlet of input buffer conveyer.
010f20 P.C.B. existence
There is no P.C.B on the positioning 1conveyor.
010f23 P.C.B. existence
There is no P.C.B on the inlet and outlet of output cnvr.
010f24 P.C.B. existence
There is no P.C.B that can be transported.
010f25 P.C.B. existence
Two P.C.Bs were detected on the supply conveyor. Please remove the P.C.B of the
conveyor entrance.
010f26 P.C.B. existence
Two P.C.Bs were detected on the output conveyor. Please remove the P.C.B on the
conveyor.
010f27 P.C.B. existence
The P.C.B was detected on the inlet of input buffer. Please remove the P.C.B.
010f28 P.C.B. existence
The P.C.B was detected on the positioning 1conveyor. Please remove the P.C.B.
2-60709-001
2.2 List of Warning Messages
Warning Codes Display Field A (Scope of Warning Messages)
Display Field B (Details of Warning Messages)
010f31 P.C.B. existence
The P.C.B was detected on the output conveyor Please remove the P.C.B.
010f32 P.C.B. existence
TherearenoP.C.Btonishat
thesametime.PleaseremoveallP.C.Bina
positioning position whether you install a there.
010f33 P.C.B. existence
AP.C.Btonishatthesametime
isnotpreparedonpositioning1conveyer.Please
remove all P.C.B whether to be put.
010f36 P.C.B. existence
A P.C.B was detected at the inlet of the input buffer conveyor. Please remove it.
010f37 P.C.B. existence
A P.C.B. was detected at the inlet of the output buffer conveyor. Please remove it.
010f38 P.C.B. existence
A P.C.B was detected at the outlet of the input buffer conveyor. Please remove it.
010f39 P.C.B. existence
A P.C.B. was detected at the outlet of the output buffer conveyor. Please remove it.
011001 Empty Feeder (rear)
Please set the feeder (rear) that used by the pattern program.
011002 Empty Feeder (rear)
-----
011101 Empty Feeder (front)
Please set the feeder (front) that used by the pattern program.
011102 Empty Feeder (front)
-----
011201 Transfer main circuit
Press [POWER ON] button to activate Load Power circuit.
011202 Transfer main circuit
Press [POWER ON] button to activate Load Power circuit.
011301 Transfer main circuit (backup, width setup)
Press [POWER ON] button to activate Load Power circuit.
011302 Transfer main circuit (backup, width setup)
Press [POWER ON] button to activate Load Power circuit.
011401 Zeroing
notnish
Perform All zeroing
011501 Feedercommunicationnotnish(rear)
Please wait for a while.
01
1601 Feedercommunicationnot
nish(front)
Please wait for a while.
011701 P.C.B. position
Please position the P.C.B.
011706 P
.C.B. position
There is no P.C.B. in the setting position.
011801 Datatransfernotnish
It cann't start because data is not set properly.
2-70802-002
2.2 List of Warning Messages
Warning Codes Display Field A (Scope of Warning Messages)
Display Field B (Details of Warning Messages)
011901 Headunsettledcomp.conrmation
An unsettled component was detected. Please discard the component. In case of
the "Pauses" condition, perform the operation for interruption.
011a01 Nozzlestockerlowerlimit
conrmation
Please perform All zeroing.
011b01 NLaxiszero
conrmation
Please perform All zeroing.
011b02 NLaxiszeroconrmation
The top and bottom axis (NL, L) by which a failure setup is carried out has fallen.
Since a zeroing cannot be performed, please raise it above a pass line manually.
011c01 Nozzle
arrangementconrmation(rear)
The nozzle arrangement of the Current Program and the head (rear) is different.
01
1d01 Nozzlearrangementconrmation(front)
The nozzle arrangement of the Current Program and the head (front) is dif
ferent.
011e01 Feeder reload (rear)
Please reload the feeder that has shortage of comp.
011f01 Feeder reload (front)
Please reload the feeder that has shortage of comp.
012001 Recycling Conveyor (rear)
Therecycle
conveyor(rear)islledup.[B0924]
012101
Recycling Conveyor (front)
Therecycleconveyor(front)islledup.[B0924]
012201
Comp. Trash Box (rear)
Thecomp.trashbox(rear)islledup.
[B0925]
012301 Comp. Trash Box (front)
Thecomp.trashbox(front)islledup.
[B0925]
012501 Data check
Error was found in internal data of the control. Please change the model or try to
save the system data.
012601 Recycling Conveyor (rear)
Please connect the recycling conveyor (rear).
012701 Recycling Conveyor (front)
Please connect the recycling conveyor (front).
012801 Tray safety door (rear)
Please close tray safety door and push tray ready sw(rear).
012901 Tray safety door (front)
Please close tray safety door and push tray ready sw(front).
012a01 Tray shotage Comp (rear)
Please supply comp, close tray door(rear) and push tray ready sw(rear).
012b01 Tray shotage Comp (front)
Please supply comp, close tray safety door and push tray ready sw(front).
012c01 PCB Size X
Please check the PCB size X of pattern program data.
012d01 PCB Size Y
Please check the PCB size Y of pattern program data.