4OM-1431-006_w.pdf - 第210页

3-53 Erroe ID Error Name, Description, Cause, and Remedy 4b2702 Start Process(Feeder Connect Error) A specialfeederisset.Pleaseconrmthe modelofasetfeeder . ----- 4b271 1 Start Process(Feeder Connect Error) A…

100%1 / 271
3-52
Erroe ID Error Name, Description, Cause, and Remedy
4b2411 Feeder (Movement Error)
Alarm Code:E5 - Redundant Order Error (A feeding error may occur.)
Conrmwhetherornotthetapeisbeing
jammedonthepath./Conrmthereelto
operatesmoothly./Conrmwhetherornotsomecomponentsanddustarebeing
caughtinthesprocket./Conrmwhetherornotsomecomponentsanddustare
being caught in the tape feeding gear.
4b2421 Feeder (Movement Error)
Alarm Code: E0 - Deviated origin position of the belt transfer servo motor axis.
Check whether or not the shield plate position attached to the belt transfer servo
motor axis deviated.
4b2422 Feeder (Movement Error)
Alarm Code:E1 - RS section Driving Error
Check whether or not dust adheres to the sensor position of the PS unit startup
trigger.
4b2425 Feeder (Movement Error)
Alarm Code:E4 - Positioning Completion Timeout
Check whether or not foreign particles get into the servo motor timing belt and
worm axis /worm wheel sections.
4b2426 Feeder (Movement Error)
Alarm Code:E5 - Redundant Order Error
-----
4b2427 Feeder (Movement Error)
Alarm Code:E6 - Timeout Error in Changing Servo Motor Axis.
-----
4b2428 Feeder (Movement Error)
Alarm Code:E7 - Servo ON Timeout
-----
4b2501 Failed Splicing Operation
Alarm Code:E3 - (1)No supplied history/ (2)Dirty splicing detection sensor (dust
adhesion)
(1)
Please operate to resupply components in the machine after splicing
operation.
(2) Please clean the joint detection sensor.
4b2601 Unit P.C.B. B.B.R. Information
There is no information in the relevant P.C.B. (on the Transfer Conveyor).
Delete the BBR information after removing the P.C.B..
4b2603 Unit P.C.B. B.B.R. Information
A problem was found in the unit PCB BBR information.
Delete the BBR information after removing the P.C.B..
4b2701 Start Process(Feeder Connect Error)
Aspecial
feederisappointed.Pleaseconrmthe
modelofasetfeeder.
-----
3.9 Others
0802-002
3-53
Erroe ID Error Name, Description, Cause, and Remedy
4b2702 Start Process(Feeder Connect Error)
Aspecialfeederisset.Pleaseconrmthe
modelofasetfeeder.
-----
4b2711 Start Process(Feeder Connect Error)
ACVCheckError.ComponentIDonthe
feederisnotsameasonespeciedby
current program.
-----
4b2712 Start Process(Feeder Connect Error)
Set "enable" for destination alternate feeder.
-----
4b2713 Start Process(Feeder Connect Error)
There is a splicing failure feeder.
-----
4b2721 Start Process(Feeder Connect Error)
The reel list check is not completed.
-----
4b2722 Start Process(Feeder Connect Error)
Feeder is not ready.
-----
4b2731 Start Process(Feeder Connect Error)
Please turn on the Feeder Ready SW (rear).
-----
4b2732 Start Process(Feeder Connect Error)
Please turn on the Feeder Ready SW (front).
-----
4b2733 Start Process(Feeder Connect Error)
Please set the feeder (rear) that used by the pattern program.
-----
4b2734 Start Process(Feeder Connect Error)
Please set the feeder (front) that used by the pattern program.
-----
4b2735 Start Process(Feeder Connect Error)
Feeder
communicationnotnish(rear)
-----
4b2736 Start Process(Feeder Connect Error)
Feedercommunicationnot
nish(front)
-----
4b2901 Linear Scale Error
An error for the linear scale position occurred at the beam X-axis (rear) during
zeroing operation.
Please check the linear scale attaching position on the beam X-axis (rear).
4b2902 Linear Scale Error
An error for the linear scale position occurred at the beam X-axis (front) during
zeroing operation.
Please check the linear scale attaching position on the beam X-axis (front).
3.9 Others
0802-002
3-54
Erroe ID Error Name, Description, Cause, and Remedy
4b2903 Linear Scale Error
An error for the linear scale position occurred at the beam Y-axis (rear) during
zeroing operation.
(1) Check the linear scale on the beam Y-axis (rear).
(2) Check the linear scale attaching position on the Y1 and Y2.
(3) Check if the process of the linear scale origin mark on the Y1 and Y2 has an
error.
4b2904 Linear Scale Error
An error for the linear scale position occurred at the beam Y-axis (front) during
zeroing operation.
(1) Check the linear scale on the beam Y
-axis (front).
(2) Check the linear scale attaching position on the Y1 and Y2.
(3) Check if the process of the linear scale origin mark on the Y1 and Y2 has an
error.
4b2905 Linear Scale Error
An error for the linear scale skip occurred at the beam Y-axis (rear) during zeroing
operation.
Pleaseconrm
ifthelinearscaleonthe
beamY-axis(rear)hasawsandsoil.
4b2906 Linear Scale Error
An error for the linear scale skip occurred at the beam Y-axis (front) during
zeroing operation.
Pleaseconrmifthelinearscaleonthe
beamY-axis(front)hasawsandsoil.
4b2907 Linear Scale Error
An error for the linear scale parallel offset deviation occurred at the beam Y-axis
(rear) during zeroing operation.
Please check the linear scale attaching condition on the beam Y-axis (rear).
4b2908 Linear Scale Error
An error for the linear scale parallel offset deviation occurred at the beam Y-axis
(front) during zeroing operation.
Please check the linear scale attaching condition on the beam Y-axis (front).
4b2c01 Error in communications between CPU
Failed in communications with the STG.#1 control CPU.
-----
4b2c03 Error in communications between CPU
Failed in communications with the Recog. CPU.
-----
4b2c04 Error in communications between CPU
Failed in communications with the Control CPU.
-----
3.9 Others
0802-002