4OM-1431-006_w.pdf - 第27页
Safety Precautions Safe-16 ALGE-ID Alert Indications described as " " (continuted) Alert Description Related Items The light emitter of the linear measure sensor is made of glass. If the light emitter happens t…
Safety Precautions
Safe-15
ALGE-ID
Alert Indications described as " " (continuted)
Alert Description Related Items
The load power to the motors, etc., is turned OFF but the setup
operation must be performed carefully when you put your hand
inside the machine.
"3.3.1", "3.3.2" and
"3.6" in "Chapter 3
(Vol. 1)"
This setup operation must be performed with your hands inserted
inside the machine.
Open the cover(door type) and perform the setup operation with
the load power supply to the servomotor being turned "OFF".
"5.1.2" in
"Chapter 4 (Vol. 2)"
In this teaching operation, the cover of the light source device
need not be opened.
Do not open the cover of the light source device.
The cover of the light source device, when opened, exposes users to the
high voltage components and may result in electrical shocks.
"6.5.15" in
"Chapter 4 (Vol. 2)"
•
Even when the power breaker is set to "OFF", the primary line
is powered, making it possible to cause an electric shock.
Be sure to completely stop the power supply to the machine before
maintenance work.
"1.1" in
"Chapter 1 (Vol. 4)"
•
Residual voltages may remain behind for a few minutes in the
internal devices of the machine after power interception.
Before performing maintenance work, wait until the charge lamps of
the DC power supply and the servoamplier go "OFF" in 10 minutes
or more after the power breaker is set to "OFF".
"1.1" in
"Chapter 1 (Vol. 4)"
When the at ring is cut, take care not to get injured by the
commercially available cutter.
"3.3.6" in
"Chapter 1 (Vol. 4)"
Your hand might be cut at the edge of the linear guide in the
cleaning operaiton. Wear gloves.
"3.3.8" in
"Chapter 1 (Vol. 4)"
The load power to the motors, etc., is turned OFF but the
maintenance operation must be performed carefully, protecting
your hands from any injury.
"4.5" in
"Chapter 1 (Vol. 4)"
0805-003
CAUTION
Safety Precautions
Safe-16
ALGE-ID
Alert Indications described as " " (continuted)
Alert Description Related Items
The light emitter of the linear measure sensor is made of glass.
If the light emitter happens to be damaged, be sure to suck up
the fragments with a vacuum cleaner, etc.
Do not collect the fragments with your bare hands to protect your
hands from injuries.
"4.5" in
"Chapter 1 (Vol. 4)"
CAUTION
0805-003
Safety Precautions
Safe-17
ALGE-ID
4. Alert Labels
The alert labels (described below) are used for this machine.
Please read the instructions on each label carefully and check the contents, observing the
actual object.
Be sure to follow the instructions for safety purposes.
These labels should be kept clean and easily legible at a far safe distance.
When a label has deteriorated and become illegible, contact our service department for
the replacement with a new one.
Location of Alert Labels
The alert labels are afxed on dangerous and caution-required areas.
Refer to "Alert Labels and Description" for details.
(21)
(14)
(13)
(20)
630 1000633
00
-0012-
630
10
006
33
00-0012-
630 1
00
0633
00-0012-
630
10
00633
00
-0012-
Front Side
Engage or disengage the
feeder base connector only
with the base at its lower limit.
630 127 7769
10-0112
630 1
60
5
098
10-022
6-
Do not connect
it incorrect
ly .
This s
hould only be conne
cted to
the connecto
r with a
blue circl
e mark.
Do not c
onne
ct it t
o any other c
onn
ector.
0805-003