00193370-0202.pdf - 第53页
SIPLACE Axis T est er Handbuch für das Achsprüfgerät / Axis T est er Manual Ausgabe 08/2003 Edition 6 St ructure of the user interface 53 – S hut dow n The “Shutdown ” menu contains two options: Shut do wn c omp ute r . …
Handbuch für das Achsprüfgerät / Axis Tester Manual SIPLACE Axis Tester
6 Structure of the user interface Ausgabe 08/2003 Edition
52
6 Structure of the user interface
6.1 Main menu
Fig. 6 - 1 Main menu of the user interface
The main menu is called from the axis tester start-up page. A window with the following menu op-
tions appears on screen:
–Quit
Press this button and then RETURN ( ) to close the main menu window.
– Configuration
The structure of the “Configuration” menu can be found in section 6.2
on page 54.
– Machine
The structure of the “Machine” menu is shown in section 6.3
on page 55.
– System control
The structure of the “System control” menu is explained in section 6.4
on page 56.
0DLQPHQX
6KXWGRZQ $ERXW
6\VWHPFRQWURO
&RQILJXUDWLRQ
0DFKLQH
Settings
User control
Display
Panel
Config unit
F machine
HS machine
Shutdown computer:
Shutdown computer: Yes
4XLW
Start-up window
Ports
S machine
SIPLACE Axis Tester Handbuch für das Achsprüfgerät / Axis Tester Manual
Ausgabe 08/2003 Edition 6 Structure of the user interface
53
– Shutdown
The “Shutdown” menu contains two options:
Shutdown computer. Press RETURN to exit the menu without shutting down
the axis tester.
Shutdown computer: Yes If you select this menu option and click on “Yes” to confirm,
all your settings are saved. The axis tester
is then shut down.
PLEASE NOTE: 6
Always select the “Shutdown computer: Yes” menu option to close all your activities with the
axis tester. This is the only way to store all your changes and settings in the tester, since all
changes since the last time they were saved are lost when you detach the cable from the axis
controller. 6
– About ...
This menu option calls up a window containing information about the axis tester, such as the
serial number, software version number, etc.
PLEASE NOTE: 6
Only the “Expert” user level allows access to all the menus. The default user level is “Begin-
ner”, which only allows access to the “Machine” and “About” menus. Selection of the user
level is described in section 8.1 on page 59. 6
Handbuch für das Achsprüfgerät / Axis Tester Manual SIPLACE Axis Tester
6 Structure of the user interface Ausgabe 08/2003 Edition
54
6.2 “Configuration” menu
Fig. 6 - 2 “Configuration” menu, flow chart
The “Configuration” menu has two submenus:
Panel This option is used to adapt the assignment of the four BNC outputs to your
requirements. There is a separate menu for each output. In this way, you
can connect an oscilloscope or a plotter, for example.
Config unit Each axis controller board contains three axis controllers. This menu is
used to define the sampling settings for each axis controller individually.
PLEASE NOTE: 6
Please note that your settings are not permanently saved until you select the “Shutdown” op-
tion from the main menu. 6
You can also possible permanently save your changes by selecting the “Settings” option from
the “System control” menu.
&RQILJXUDWLRQ
Window with
30 signals
Reset
Line A
Line B
Trigger
End signal
Reset
Counter
Change line 4
Change line 3
Change line 2
Change line 1
Activate panelChange panelOverspeedSampling
Selection 1/2/3/4
Panel
Select unit 1/2/3
Config unit