00193370-0202.pdf - 第55页
SIPLACE Axis T est er Handbuch für das Achsprüfgerät / Axis T est er Manual Ausgabe 08/2003 Edition 6 St ructure of the user interface 55 6.3 “Machine” menu Fig. 6 - 3 “Machine” menu, flow chart The “Mac hine” menu con t…
Handbuch für das Achsprüfgerät / Axis Tester Manual SIPLACE Axis Tester
6 Structure of the user interface Ausgabe 08/2003 Edition
54
6.2 “Configuration” menu
Fig. 6 - 2 “Configuration” menu, flow chart
The “Configuration” menu has two submenus:
Panel This option is used to adapt the assignment of the four BNC outputs to your
requirements. There is a separate menu for each output. In this way, you
can connect an oscilloscope or a plotter, for example.
Config unit Each axis controller board contains three axis controllers. This menu is
used to define the sampling settings for each axis controller individually.
PLEASE NOTE: 6
Please note that your settings are not permanently saved until you select the “Shutdown” op-
tion from the main menu. 6
You can also possible permanently save your changes by selecting the “Settings” option from
the “System control” menu.
&RQILJXUDWLRQ
Window with
30 signals
Reset
Line A
Line B
Trigger
End signal
Reset
Counter
Change line 4
Change line 3
Change line 2
Change line 1
Activate panelChange panelOverspeedSampling
Selection 1/2/3/4
Panel
Select unit 1/2/3
Config unit
SIPLACE Axis Tester Handbuch für das Achsprüfgerät / Axis Tester Manual
Ausgabe 08/2003 Edition 6 Structure of the user interface
55
6.3 “Machine” menu
Fig. 6 - 3 “Machine” menu, flow chart
The “Machine” menu contains preconfigured test set-ups for each type of machine:
HS machines This menu contains the axis configuration for 4-gantry placement ma-
chines.
S machines This menu contains the axis configuration for 2-gantry placement machines
and the glue dispenser.
F machines This menu contains the axis configuration for 1-gantry placement machines
and the wafflepack changer (WPC).
BackCursor T1 Cursor T2
Proceding
Grafics w. cursor
QuitStart plotStart FFT
Waiting f. Trigger Start window
OverspeedPositioning timeLine errorReference error
Track signalsMachine info Adjust panelPos. qualitySerial connect.
Select axis / Properties
HS-50
F3, F4, F5,
F5 HM, WPC
F machine
S-15, S-20, S-23
S-25, G
HS machine
S machine
BNC 1/2/3/4
Dynamic
RETURN
Press any key
to go back
Press any key
to go back
BNC 1/2/3/4
Static
Select PWM mode
These menus can only be accessed
if the previous measurement was successful.
Back to Positioning
time menu
Handbuch für das Achsprüfgerät / Axis Tester Manual SIPLACE Axis Tester
6 Structure of the user interface Ausgabe 08/2003 Edition
56
6.4 “System control” menu
Fig. 6 - 4 “System control” menu
The “System control” menu has four submenus:
Settings This menu is used to save your individual settings or load settings that you
have already stored.
User control Allows you to select the user interface language. There are two versions –
German and English.
Also used to select the user level. There are two options: “Beginner” and
“Expert”. “Beginner” is set by default.
Display This menu is used to set the appearance of the user interface and screen
saver.
Ports Used to define the parameters for the CAN bus and serial port.
EEPROM
DisplayUser controlSettings
Save ...
Load ...
Default
Beginner
Language
German
English
User level Set contrast
Darker
Brighter
Screen saver
Stars
Change type
Display off
Settings
Enable
Reset
Disable
Delay
Max. 2 h
CAN port
CAN IDS
Serial port
Change ASC port
Sending CT ID
Sending events ID
Receiving ID
SAT-A36X
SAT-PC
A36X-PC
Ports