00193370-0202.pdf - 第80页

Handbuch für das Achsprüfgerät / Axis T ester Manual SIPLACE Axis T e ster 8 Using the menus Ausgabe 08/2003 Edition 80 The menu for loading se ttings appea rs. Fig. 8 - 50 “Load settings” menu 8.5.2 “User” menu The “Use…

SIPLACE Axis Tester Handbuch für das Achsprüfgerät / Axis Tester Manual

Ausgabe 08/2003 Edition 8 Using the menus

8.5 “System control” menu

You can use this menu to

– save and reload the settings for your axis tester,

– change the display language,

– configure the display and

– define the parameters for the CAN bus and serial ports.

Æ To do this, select the “System control” option from the main menu.

Fig. 8 - 47 Main menu, selecting the “System control” menu

The ‘System control menu appears.

Fig. 8 - 48 “System control” menu

8.5.1 “Settings” menu

Æ Select the “Settings” menu. The window for loading and saving the axis tester configuration

appears.

Fig. 8 - 49 “Settings” menu, loading or saving settings

Æ Select the “Load …” menu option.

For saving and loading settings

User level and language

Display: contrast and screen saver

CAN bus and serial port

Reserved for servicing purposes

Menu option for loading settings

The settings are stored in the EEPROM of the

axis tester.

Handbuch für das Achsprüfgerät / Axis Tester Manual SIPLACE Axis Tester

8 Using the menus Ausgabe 08/2003 Edition

The menu for loading settings appears.

Fig. 8 - 50 “Load settings” menu

8.5.2 “User” menu

The “User” menu allows you to select the user interface language: German or English. You can

also set the user level. At the “Beginner” user level, you only have access to a limited choice of

menus from the user interface.

Fig. 8 - 51 “User” menu

8.5.3 “Display” menu

Æ Select the “Display” option from the “System control” menu.

The menu for configuring the CAN connection and serial port appears.

Fig. 8 - 52 “Display” menu

Factory defaults that cannot be modified

Here you can adopt the most recently saved

settings

“Yes” to accept

“Back” to cancel

Select German or English as the interface

language

Select “Expert” or “Beginner” as the user

level: if you choose “Beginner”, then the num-

ber of options in the “Machine” and “About”

menus is limited. Selection of the user level

is described in section 8.1

on page 59.

Display contrast settings:

Brighter ↔ Darker

Screen saver configuration:

- Duration

- Change type

- Set the delay

SIPLACE Axis Tester Handbuch für das Achsprüfgerät / Axis Tester Manual

Ausgabe 08/2003 Edition 8 Using the menus

8.5.4 “Ports” menu

Æ Select the “Ports” option from the “System control” menu.

The menu for configuring the CAN and serial ports appears.

Fig. 8 - 53 “Ports” menu

8.5.4.1 “CAN port” menu

Select the “CAN IDs” option from the “CAN port” menu. Here you can change the sending or re-

ceiving address.

Fig. 8 - 54 “CAN IDs” menu

Fig. 8 - 55 “Sending CT-ID” window

Use the and cursor keys to change the numbers, and the and

cursor keys to select the position within the hex number.

Configure the CAN ID

Configure the serial port

If you select “Sending CT-ID”, the window for

entering the hex address appears.

CAUTION: 8

Do NOT change the default hex value, since

this will prevent communication being estab-

lished with the axis controller. 8