D-serie LEVEL II.pdf - 第179页
Modular Conveyor Setting the Fixed Conveyor Side (Single and D ual Conveyor) Conveyor Settings S tude nt Guide Advanced Level 2 SIPLACE D Series EN 05/2007 Modular Conveyor 10-13 T o (2), (3): Advanced Conveyor Configura…
Modular Conveyor
Conveyor Settings Setting the Fixed Conveyor Side (Single and Dual Conveyor)
Student Guide Advanced Level 2 SIPLACE D Series
Modular Conveyor EN 05/2007
10-12
10.3.1 Setting the Fixed Conveyor Side (Single and Dual Conveyor)
10.3.1.1 General Notes
10-4: SITEST – conveyor "options and configuration"
See also:
J To (1): Reference Position of Fixed Side [J10-12]
J To (2), (3): Advanced Conveyor Configuration [J10-13]
J To (3): Widening the Conveyor (Flexible Dual Conveyor for Single Conveyor Mode) [J10-13]
J To (3): Converting the Single Conveyor Mode Back to Flexible Dual Conveyor Mode [J10-14]
J To (2): Setting the Fixed Conveyor Side for "Extra Wide" Mode [J10-15]
To (1): Reference Position of Fixed Side
The fixed conveyor side can be changed via SITEST and set to "Right side fixed"/"Left side fixed" as
required.
If the position of the fixed conveyor side which has been taught is saved, these values will be used
for the function
Move all conveyor edges to standard position
.
The default values will be overwritten and will need to be retaught.
If these dimensions are incorrectly set on the single or dual conveyor, the PCB reference corner may
be moved, leading to fiducial errors during placement.
NOTE:
In the SR/MC station SW, the fixed conveyor side of all lanes can be adjusted in the conveyor
firmware (flexible). However, this may only be set with the SITEST software.
NOTE:
If you want to change the conveyor mode from "widened" to "extra wide" (or vice versa), you
need to first move the conveyor back into standard mode and then select the new mode.
NOTE:
The menu (1) is protected with the Siemens Service password.
Modular Conveyor
Setting the Fixed Conveyor Side (Single and Dual Conveyor) Conveyor Settings
Student Guide Advanced Level 2 SIPLACE D Series
EN 05/2007 Modular Conveyor
10-13
To (2), (3): Advanced Conveyor Configuration
Two requirements for changing the fixed conveyor sides:
Extra wide conveyor: This moves the fixed conveyor side in D-series machines 25 mm (D3: X extra
wide 34 mm) outwards.
Widen conveyor:This moves the conveyor sides of the 2nd conveyor to the limit switch
In single conveyor mode, lane 1 of D-series machines can be set to widths of up to 380 mm (HF, X,
D3 lines up to 450 mm).
To (3): Widening the Conveyor (Flexible Dual Conveyor for Single Conveyor Mode)
X Select
Option and configuration
from the SITEST conveyor menu and then click on
Widen
conveyor
to widen the conveyor.
X The conveyor sides of the 2nd conveyor lane (right side fixed (lane 1 left side fixed)) are moved to
the limits.
X The SITEST SW ask for connecting the lifting tables.
Widening the board conveyor (from its standard width) allows you to use boards up to 380 mm wide.
If the PCB conveyor is switched from the mode "extra wide" to the mode "widened", this means that D-
series machine can place boards up to a width of approx. 400 mm (D3: approx. 420 mm).
10-5: Setting the "fixed conveyor side" in SIPLACE D-Series
NOTE:
The fixed conveyor side should be adjusted only with the SITEST software and the width
adjustment devices. This ensures that the conveyor runs straight.
Modular Conveyor
Conveyor Settings Setting the Fixed Conveyor Side (Single and Dual Conveyor)
Student Guide Advanced Level 2 SIPLACE D Series
Modular Conveyor EN 05/2007
10-14
Connecting the Dual Conveyor Lifting Tables
X Remove the lifting table plate on conveyor lane 2 in PA1 and on lane 1 in PA2.
X Loosen the lockscrew(s) (4) and use a screwdriver to push the hexagonal circlip over the shaft on
lifting table 1.
X Do this for lifting tables in all placement areas. (lifting tables in the PA’s 180° turned.)
X Configure the new conveyor mode in SIPLACE Pro
To (3): Converting the Single Conveyor Mode Back to Flexible Dual Conveyor Mode
X Select the SITEST conveyor menu "Option and configuration" and then click on
Widen conveyor
to set the standard conveyor mode.
X The flexible conveyor side of conveyor 1 (right side fixed (track 1 left side fix)) is moved to a small
conveyor width.
X The SITEST SW ask to disconnect the lifting tables - Do so-.
X The SITEST SW will now use the conveyor control SW to move the fixed side of conveyor 2 (right
side is fixed (lane 1 left side fixed)) back to its standard position. Check the distances between the
two fixed conveyor lanes.
X Now adjust conveyor width of both tracks to desired values.
NOTE:
This option is only a mechanical function when you use the dual conveyor as a single conveyor.
The two lifting tables move parallel when they are connected.
10-6: Lifting table
The drive shaft (1) is connected to the piston
rod of the pneumatic cylinder. This shaft
couple the second lifting table of the dual
conveyor. The lifting table drive shaft also has
an additional rod with a hexagonal circlip.
They secure the sleeve shaft in the desired
position.
Direction of transport (2)
Direction (3) in which the hollow shaft from
lifting table 2 (1 in PA 2) is to be moved to lifting
table 1 (2 in PA 2).
Lock screws (4)
NOTE:
When converting the dual conveyor to a single conveyor (flexible dual conveyor, connect the
lifting tables when requested to do so by SITEST (we recommend doing this without
compressed air supply to the lifting table).
This function is supported by SIPLACE Pro.