MIL- STD-883F 2004 TEST METHOD STANDARD MICROCIRCUITS.pdf - 第468页

MIL-STD-883F METHOD 2032.2 18 June 2004 62 3.3.6 I nductor and trans former defect s, "l ow magnific ation" . No element shall be ac cept able that e xhib its: a. Peel ing, l ifti ng or bli ster ing of windi ng…

100%1 / 708
MIL-STD-883F
METHOD 2032.2
18 June 2004
61
Class H Class K
3.3.4 e. Metallized terminal not aligned as shown in 3.3.4 e. Same as class H.
the applicable drawing.
f. Encapsulant preventing the metallized f. Same as class H.
terminal from resting on the substrate
bonding pads when the capacitor is in
the bonding position except where the
metallized terminal electrical contact
is made by alternate means.
g. Lifting, blistering or peeling of metallized g. Same as class H.
terminal encapsulant.
3.3.5 Parallel plate chip capacitor defects,
"low magnification"
. No element shall be acceptable
that exhibits:
a. Metallization that extends greater than 50 a. Same as class H.
percent around the edge of the capacitor
(see figure 2032-60h).
FIGURE 2032-60h. Class H metallization extension criterion
.
3.3.5 b. Evidence of cracks in the dielectric body 3.3.5 b. Same as class H.
(see figure 2032-61h).
FIGURE 2032-61h. Class H crack in dielectric criterion
.
MIL-STD-883F
METHOD 2032.2
18 June 2004
62
3.3.6 Inductor and transformer defects, "low
magnification"
. No element shall be acceptable
that exhibits:
a. Peeling, lifting or blistering of winding a. Same as class H.
metallization or insulation.
b. Evidence of shorts between adjacent turns or b. Same as class H.
windings.
c. Cracks or exposure of bare magnetic core c. Same as class H.
material. Exposed bare magnetic core material
is acceptable if by design.
d. Pits or voids in the core insulation greater d. Same as class H.
than 5.0 mils area that expose the magnetic
core material.
e. Separation less than 5.0 mils between wire e. Same as class H.
termination points of the same or adjacent
windings.
f. Missing polarity identification unless by f. Same as class H.
design.
g. Operating metallization and multilevel thick g. Same as class H.
film defects as described in 3.2.1 and
3.2.5 herein.
3.3.7 Chip resistor defects, "low magnification"
.
No element shall be acceptable that exhibits:
a. Reduction of the resistor width resulting from a. Same as class H.
voids, bubbles, nicks, or scratches, or a
combination of these, that leaves less than 50
percent of the narrowest resistor width (see
figure 2032-62h).
FIGURE 2032-62h. Class H resistor width reduction criterion
.
MIL-STD-883F
METHOD 2032.2
18 June 2004
63
Class H Class K
3.3.7 b. A kerf that leaves less than 50 percent 3.3.7 b. Same as class H.
of the original width of the resistor
unless by design.
c. Metallized termination width less than c. Same as class H.
10.0 mils unless by design
(see figure 2032-63h).
FIGURE 2032-63h. Class H termination width criterion
.
d. A crack, chipout or void in the substrate d. Same as class H.
greater than 3.0 mils in any direction (see
figure 2032-64h).
FIGURE 2032-64h. Class H substrate defect criteria
.