00191369-02.pdf - 第101页

User Manual HS-50 3 Introduction and Basic Concepts Software Vers ion SR.501.xx 12/99 Issue US 3.1 Mac hine Displays a nd Controls 101 t I I t 3.1.4 Barcode Reade r The barco de reade r is avail able as an o ption. It i …

3 Introduction and Basic Concepts User Manual HS-50

3.1 Machine Displays and Controls Software Version SR.501.xx 12/99 Issue US

100

t IIt

(Top lamp)

(Middle lamp)

(Bottom lamp)

Meaning

Status display

flashes (1,10) flashes (7,7) flashes (1,10) Reference run

unchanged flashes (1,5) unchanged Waiting until axes in position

unchanged flashes (7,7) unchanged Waiting for setup data

unchanged flashes (7,7) unchanged Waiting for cluster data

unchanged flashes (7,7) unchanged Load table program

unchanged flashes (7,7) unchanged Position recognition

unchanged flashes (1,10) unchanged Ink spot recognition

unchanged flashes (7,7) unchanged Nozzle configuration test

unchanged flashes (7,7) unchanged Feeder posn. recogn.

unchanged flashes (7,7) unchanged One track is empty

unchanged flashes (7,7) unchanged No further track available

unchanged flashes (7,7) unchanged Go to refill position

unchanged flashes (7,7) unchanged Transport being initialized

unchanged flashes (7,7) unchanged Place PCB in input conveyor

flashes (1,10) flashes (7,7) unchanged Remove PCB from output conveyor

unchanged flashes (7,7) flashes (1,10) Remove PCB in output conveyor 2

flashes (1,10) flashes (7,7) flashes (1,10) Width adjustment

unchanged flashes (1,10) unchanged Transport PCB

flashes (1,10) flashes (7,7) flashes (1,10) Both output conveyors are cleared

on flashes (1,10) on Transport errors

on off on Go to service position

on Placement

flashes (1,20) Waiting for processing data

Error display

on off unchanged Machine error, right

on off unchanged Track empty, right

on off unchanged Nozzle configuration, right

on off unchanged Transport error, right

on off on Fiducial error, left and right

unchanged off on Track empty, left

unchanged off on Nozzle configuration, left

unchanged off on Transport error, left

unchanged off on Machine error, left

Pick-up error display

unchanged unchanged flashes (1,20)

First track empty, left

unchanged unchanged flashes (5,20)

Further tracks empty, left

unchanged unchanged flashes (5,5)

Penultimate track in use, left

unchanged unchanged flashes (1,2)

Last track in use, left

flashes (1,20) unchanged unchanged

First track empty, right

flashes (5,20) unchanged unchanged

Further tracks empty, right

flashes (5,5) unchanged unchanged

Penultimate track in use, right

flashes (1,2) unchanged unchanged

Last track in use, right

Tab. 3.1 - 1 Standard configuration for the main fault indicator

User Manual HS-50 3 Introduction and Basic Concepts

Software Version SR.501.xx 12/99 Issue US 3.1 Machine Displays and Controls

101

t IIt

3.1.4 Barcode Reader

The barcode reader is available as an option. It is very helpful, particularly under production

conditions, since component barcodes on component reels and track barcodes can be read in

quickly and reliably from the barcode strip on the machine.

An acoustic signal sounds each time a data record is successfully read in.

NOTE

For a detailed description of the function, connection and operation of the bar code reader, refer

to chapter 11 "Station extensions / hardware". 3

3.1.5 Station Computer

The station computer is located in a midi tower housing and is equipped with a 3 ½" floppy disk

drive and CD-ROM drive. 3

NOTE

The SC software is installed under the NT 4.0 operating system. To prevent damage to the oper-

ating system in the event of a power failure, the station computer is connected to an uninterruptible

power supply (UPS, see Section 3.1.6). 3

3.1.6 Uninterruptible Power Supply UPS

The UPS is located directly next to the station computer. It is used to boost insufficient mains

power supplies and bridge over mains voltage failures. This guarantees that the connected de-

vices can continue to function even if the power supply fails and that a controlled power-down of

the station computer can be performed. 3

CAUTION

Before the UPS is used for the first time, it must be charged for approximately 24 hours (because

of charge loss due to storage) in order to guarantee secure computer system operation. 3

NOTE

A separate manual is supplied with the UPS.

Please refer to this manual for a description of the connections, displays and setting options. Pay

close attention to the safety instructions and warnings it contains. 3

3 Introduction and Basic Concepts User Manual HS-50

3.1 Machine Displays and Controls Software Version SR.501.xx 12/99 Issue US

102

t IIt

3.1.7 Monitors

The 13.8" monitors (TFT-LCD flat screens) with integrated touch screen which are installed on ei-

ther side of the machine act as the display and operating tool for the graphic user interface of the

SC software. You select functions using your finger which guides the mouse pointer over the

screen itself.

Actions can be executed by touching the corresponding object (e.g. button or icon) on the screen. 3

CAUTION

Protect the monitor from humidity and excessive heat (sunlight, room heating).

Never obstruct the ventilation slots.

Never try to remove the cover.

Make sure that no moisture is able to penetrate the inside of the monitor.

Make sure that the operating voltage is set correctly.

Make sure that the brightness and contrast of the screen display are set to medium values since

these greatly prolong the lifetime of the screen. 3

NOTE

Each monitor is supplied with a separate User Manual and you should follow the warnings and

safety instructions it contains.

Please refer to the Manual for a description of the connections and setting options. By default, the

resolution of the screen display is set to 1024 x 768 pixels. 3