OM-1606-006w_GT-28x.pdf - 第22页

Contents Cont-4 Page OM-1606 1005-002 6.7 24 mm Width T ape Splicing Procedure ................................... 6-20 6.7.1 Cutting New T ape ......................................................... 6-20 6.7.2 Cutting…

100%1 / 235
Contents
Cont-3
Page
OM-1606
1005-002
4. Operation Panel .............................................................................4-1
4.1 Name and Function of Each Section on Operation Panel ......4-1
4.2 Operation of Operation Panel .................................................4-3
4.2.1 Subject Lane Selection ..................................................4-3
4.2.2 Feed Pitch Selection ...................................................... 4-3
4.2.3 Set Pitch Feeding Operation .........................................4-4
4.2.4 Minimum Pitch Feed Operation .....................................4-4
4.2.5 Set Pitch Returning Operation .......................................4-5
4.2.6 Minimum Pitch Returning Operation ..............................4-6
4.2.7 Cover Tape Take-up Operation ...................................... 4-7
4.2.8 Continuous Feeding Operation ......................................4-8
4.2.9 Cancel the tape feed speed deceleration to return ........4-8
4.2.10 I/O Status Indication for Sensor, etc. .............................4-9
4.3 Error Codes and Splicing Guide .............................................4-11
4.3.1 Feeder Operation Error Codes ......................................4-11
4.3.2 Servo Alarm System Error Codes .................................. 4-15
4.3.3 Splicing Guide ...............................................................4-17
5. Component Pick-up Position Alignment .........................................5-1
6. Splicing ........................................................................................... 6-1
6.1 Preparation of Splicing ............................................................ 6-1
6.2. Setting in the Main Machine before Splicing Operation ..........6-2
6.2.1 Setting in the Splicing Stop and Warning Mode ............6-2
6.3. Indication of "Alarm for Splicing"
on the Machine Information Window ......................................6-4
6.3.1 Characteristics of the Tape Feeders applicable
to the Splicing Operation ...............................................6-4
6.4 Splicing Operation ..................................................................6-6
6.5 8 mm Width Tape Splicing Procedure ..................................... 6-8
6.5.1 Cutting New Tape ..........................................................6-8
6.5.2 Cutting Tape on Feeder Side .........................................6-9
6.5.3 Tape Splicing Procedure (For 8 mm : HT8RE) .............6-10
6.5.4 Precautions .................................................................... 6-12
6.6 12 mm and 16 mm Width Tape Splicing Procedure ................ 6-14
6.6.1 Cutting New Tape ..........................................................6-14
6.6.2 Cutting Tape on Feeder Side .........................................6-15
6.6.3 Tape Splicing Procedure
(For 12 mm : FC12QE, 10896-96-430 (For backing), For 16 mm :
FC16QE, 10896-96-430 (For backing)) .........................6-16
6.6.4 Precautions .................................................................... 6-18
Contents
Cont-4
Page
OM-1606
1005-002
6.7 24 mm Width Tape Splicing Procedure ................................... 6-20
6.7.1 Cutting New Tape .........................................................6-20
6.7.2 Cutting Tape on Feeder Side .........................................6-21
6.7.3 Tape Splicing Procedure
(For 24 mm or more : FC24QE) ....................................6-22
6.7.4 Precautions .................................................................... 6-24
6.8 32 mm Width Tape Splicing Procedure ................................... 6-26
6.8.1 Cutting New Tape ..........................................................6-26
6.8.2 Cutting Tape on Feeder Side .........................................6-27
6.8.3 Tape Splicing Procedure
(For 24 mm or more : FC24QE) ....................................6-28
6.8.4 Precautions .................................................................... 6-30
6.9 44 mm, 56 mm, 72 mm and 88 mm
Width Tape Splicing Procedure ............................................... 6-32
6.9.1 Cutting New Tape ..........................................................6-32
6.9.2 Cutting Tape on Feeder Side .........................................6-34
6.9.3 Tape Splicing Procedure
(For 24 mm or more : FC24QE) ....................................6-35
6.9.4 Precautions .................................................................... 6-38
6.10 Splicing Procedure using a pocket on the carrier tape ...........6-40
6.10.1 Cutting New Tape ..........................................................6-40
6.10.2 Preparation of Carrier Tape for Joint .............................6-41
6.10.3 Cutting Tape on Feeder Side .........................................6-42
6.10.4 Tape Splicing Procedure ................................................6-43
6.10.5 Precautions .................................................................... 6-45
6.11 Splicing Procedure using a Metal Plate ..................................6-46
6.12 Conrmation of the No. of Components to be replenished .....6-48
Contents
Cont-5
Page
OM-1606
1011-002
7. Maintenance ................................................................................... 7-1
7.1 Precautions before Maintenance ............................................7-1
7.2 Preparation for Maintenance ..................................................7-2
7.3 Maintenance Check List .........................................................7-4
7.3.1 Daily Maintenance in Each Section ...............................7-4
7.3.2 Weekly Maintenance .....................................................7-4
7.3.3 Quarterly Maintenance ..................................................7-4
7.4 Maintenance Spots .................................................................7-5
7.4.1 Description of Maintenance in Each Section .................7-5
7.4.2 Suppressor Section .......................................................7-6
7.4.3 Cover Tape Take-up Section .........................................7-8
7.4.4 Component Discharging Section ...................................7-9
7.4.5 Joint Detection Unit .......................................................7-10
7.4.6 Tape Feed Gear Section ................................................7-11
7.4.7 Cover Tape Take-up Gear Section ................................7-11
7.5 Maintenance Method ..............................................................7-12
7.5.1 How to Apply Grease
to the Sprocket Driving Gear Unit ..................................7-12
7.5.2 8 mm Dual Feeder Joint Detection Unit Sensor
Section Cleaning
(GD-28080, GD-28081, GD-28082, GD-28083) ............7-16
7.5.2.1 Spots to be Cleaned ...............................................7-16
7.5.2.2 How to Clean the Sensor Section ..........................7-16
7.5.2.3 Sensor Detection Check ........................................7-18
7.5.3 Wide Feeder Joint Detection Unit Sensor
Section Cleaning
(GD-12162, GD-24322, GD-44562, GD-72002,
GD-88002) .....................................................................7-20
7.6 Maintenance Component List .................................................7-22