APC - 224650 Issue 1.pdf - 第37页

ALL PURPOSE CLAMPING (APC) ADJUSTMENTS AND SETTINGS Chapter Issue 1 Nov 16 All Purpose Clamping (APC) Manual 1.25 13. Ensure that Home Rail W idth is highlighte d. 14. Select Run Diagnost . 15. Select Exit . 16. Use Next…

100%1 / 112
ALL PURPOSE CLAMPING (APC)
ADJUSTMENTS AND SETTINGS
1.24 All Purpose Clamping (APC) Manual Chapter Issue 1 Nov 16
4. Remove the board from the rails and confirm the amber LED extinguishes.
5. Turn the board 90° and position back onto the rail system (so that the board
lies on top of the rail system as shown in the graphic below).
6. Confirm that the amber LED is extinguished. If the amber LED illuminates,
turn the sensitivity control anti-clockwise until the amber LED extinguishes.
7. Remove the board.
8. Position the board back on the rail system, as in Step 1, and confirm that the
amber LED illuminates.
9. If the board has holes or cut-outs, go to Step 10.
Otherwise, go to Step 13.
10. Slide the board backward and forward across the sensor ensuring that the
LED is only triggered by the leading and trailing edges of the board.
11. If the LED flickers when encountering holes or cut-outs, turn the sensitivity
control clockwise a further quarter turn.
12. Repeat Steps 10 and 11 until the correct setting is achieved.
13. Remove the board from the rails and confirm that the amber LED extin-
guishes.
Front Rail
Parallelism
1. Select Open Cover Commands.
2. Select Carriage To Rear.
3. Select Unload Screen.
4. Open the front printhead cover.
5. Remove the screen from the machine.
6. Close the front printhead cover.
7. Press the System button.
8. Select Back.
9. Select Maintenance.
10. Select Diagnostics.
11. Use Next or Previous to highlight Rail System.
12. Select Select Module.
ALL PURPOSE CLAMPING (APC)
ADJUSTMENTS AND SETTINGS
Chapter Issue 1 Nov 16 All Purpose Clamping (APC) Manual 1.25
13. Ensure that Home Rail Width is highlighted.
14. Select Run Diagnost.
15. Select Exit.
16. Use Next or Previous to highlight Rising Table.
17. Select Run Diagnost.
18. Use Next or Previous to highlight Rising Table to Transport Height.
19. Select Run Diagnost.
20. Open the front printhead cover.
21. Remove any tooling from the manual tooling plate.
22. Place the rail setting jigs (Part No 205816) on the manual tooling plate,
spaced approximately 275mm apart about the centre, ensuring that they are
against the front of the table.
23. Using the jog buttons, carefully lift the table until the rails are clear of the
clatter bars.
24. Using a 0.05mm feeler gauge as a no-go gauge, check positions 1 and 2
(shown in graphic) on both rail setting jigs.
If a gap >0.05mm is present, adjustment is needed. Continue at Step 25.
If adjustment is not necessary continue at Step 31.
View on Rear of Front Rail
0.05mm Feeler Gauge
1
2
ALL PURPOSE CLAMPING (APC)
ADJUSTMENTS AND SETTINGS
1.26 All Purpose Clamping (APC) Manual Chapter Issue 1 Nov 16
25. Using a 3mm Allen key slacken the four retaining screws, passing through
the upper bearing carriage and connecting mount, and attaching the left
hand transport leg to the rail support arm. Repeat for the lower bearing
carriage.
26. Repeat Step 25 for the right hand transport leg.
27. Move the transport rail until it sits snugly in both rail setting jigs. The correct
setting is shown in Step 24.
28. Tighten the retaining screws on both the left and right hand upper bearing
carriages.
29. Recheck the parrallelism as detailed in Step 24.
30. Tighten the retaining screws on both the left and right hand lower bearing
carriages.
31. Remove the rail setting jigs from the rising table.
32. Close the front printhead cover.
33. Press the System button.
34. Select Exit.
35. Select Exit.
36. Select Back.
Rear Rail
Parallelism
NOTE
Ensure Front Rail Parallelism has been carried out prior to commencing this
procedure. It is recommended that the rear rail parallelism procedure is carried
out by two persons.
1. Select Shut Down.
2. Select Continue.
3. Switch the mains isolator to OFF.
4. Remove the left and right hand side panels (if necessary, disconnect the air
and electrical supplies and remove the printer from the production line).
Upper Bearing Carriage
Upper Rail Support
Arm Screws (4 off)
Lower Bearing Carriage
Lower Rail Support
Arm Screws (4 off)